4-5: Delay T01-08, 4-6: Delay T09-16 - Korg M3 Parameter Manual

Bottom Slope
Specifies the number of velocity steps over which the
original volume will be reached, starting from the Bottom
Velocity.
0: The volume will be at the original value from the bottom
velocity.
120: The volume will decrease as the velocity approaches the
bottom velocity.
Bottom Velocity
Specifies the minimum velocity value that will sound each
timbre.
How volume will change according to keyboard location
Volume
Bottom Slope
Bottom Velocity
Top Velocity and Bottom Velocity settings can also be input
by holding down the ENTER switch and playing a note on
the keyboard.
Timbre 02...08, 09...16 (Timbre Number):
These are the velocity zone settings for timbres 2–8 and 9–
16. They are the same as for timbre 1. For more information,
please see "Timbre 01 (Timbre Number):," above.
▼4–3(4): Menu Command
• 0: Write Combination ☞p.185
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy from Program ☞p.185
For more information, please see "Combination: Menu
Command" on page 185.
COMBI P4: Zone/Delay 4–5: Delay T01–08, 4–6: Delay T09–16
[000...120]
[001...127]
Velocity
Top Slope
Top Velocity
4–5: Delay T01–08,
4–6: Delay T09–16
4–5a
4–5b
4–5c
This specifies the time (delay) from when the timbres 1–8
and 9–16 receives a note-on until the sound begins.
4–5(6)a: Combination Name, Tempo
4–5(6)b: Timbre Info
For more information, please see "2–1: EQ Trim T01–08, 2–2:
EQ Trim T09–16" on page 147.
4–5(6)c: Delay
Timbre 01 (Timbre Number):
Delay Time [ms]
Specifies the time (delay time) from note-on until the timbre
begins to produce sound, in units of ms (1/1000th of a
second). This setting is available if MIDI/Tempo Sync. is set
to Off.
KeyOff: The note will begin sounding at note-off. In this
case, the sound will not die away if the sustain level of the
program's amp EG is other than 0. This setting is used when
creating harpsichord sounds.
Normally you will set this to 0000.
MIDI/Tempo Sync.
The time (delay time) from note-on until the timbre
produces sound will be specified in note length units
relative to the (Tempo).
On (checked): Specify the delay time in terms of a Base
Note and Times relative to the Tempo. For example if Base
Note = , Times = 01, and Tempo = 60 BPM, the delay time
will be equivalent to 1000 ms.
Off (unchecked): The delay time will be set by the Delay
Time setting.
Base Note [ ,
Times
It specifies the time (delay time) from note-on until the
timbre begins to produce sound, in terms of a note value
relative to the (Tempo) (Combi 0–1(2)a).
Use Base Note to specify the desired note value, and use
Times to extend that note value by the specified multiple.
For example if you set Base Note to a quarter note ( ) and
Times to 02, that timbre will sound with a delay of a half
note ( ). Even if you change (Tempo) (Combi 0–1(2)a), the
delay time will always be a half note ( ). If you use these
parameters to specify a delay of a half note ( ). In this case,
a Tempo of 60.00 BPM will produce a 2000 ms delay, and a
Tempo of 120.00 BPM will produce a 1000 ms delay.
4–5
Menu
[0000...5000ms, KeyOff]
[Off, On]
, , , , , , , , ]
[01...32]
155