061: Tape Echo; 062: Auto Reverse - Korg M3 Parameter Manual

Effect Guide

061: Tape Echo

This effect simulates a tape echo unit with three playback
heads. The distortion and tonal change typical of magnetic
tape are also reproduced.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Saturation
Trim Pre Tone
Right
D -mod
Delay (Tap1)
0...2700
[msec]
a Src Off...Tempo
–2700...
Amt
+2700
b Tap2
0...100
Position [%]
Tap3
c 0...100
Position [%]
Tap1 Level 0...100
Pan L, 1...99, R
d
FB Amt –100...+100
Tap2 Level 0...100
Pan L, 1...99, R
e
FB Amt –100...+100
Tap3 Level 0...100
Pan L, 1...99, R
f
FB Amt –100...+100
Feedback 0...100
g
Src Off...Tempo
Amt –100...+100
High Damp
0...100
[%]
h
Low Damp
0...100
[%]
i Saturation 0...100
Input Trim 0...100
j
Pre Tone 0...100
Wow Flutter
0.02...1.00
[Hz]
k
Wow Flutter
0...100
depth
Dry,
Wet/Dry 1 : 99...99 : 1,
Wet
l
Src Off...Tempo
Amt –100...+100
a: Delay (Tap1) [msec]
a: Src
a: Amt
b: Tap2 Position [%]
b: Tap3 Position [%]
The delay time for Tap 2 and 3 is specified as a proportion
(%) relative to Delay (Tap1). Even if you use dynamic
modulation to control Delay (Tap1), Tap 2 and 3 will change
at the same proportion.
480
(3)
(2)
(1)
Feedback Amt Level Pan
Tape
Delay
High / Low Damp
Tap2/3
Wah Flatter
Position
Delay Time
Sets the delay time (tap1)
p.480
Selects the modulation source
of the delay time p.480
Sets the modulation amount of
delay time p.480
Sets the position of Tap 2
relative to the Tap 1 delay time
the depth of pitch variation
p.480
Sets the position of Tap 3
relative to the Tap 1 delay time
the depth of pitch variation
p.480
Sets the Tap1 output level
Sets the stereo image of tap1
Sets the Tap1 feedback amount
p.480
Sets the Tap2 output level
Sets the stereo image of tap2
Sets the Tap2 feedback amount
p.480
Sets the Tap3 output level
Sets the stereo image of tap3
Sets the Tap3 feedback amount
p.480
Sets the amount of feedback
for Taps 1, 2, and 3 p.480
Selects the modulation source
of feedback amount
Sets the feedback amount
Sets the damping amount in
the high range
Sets the damping amount in
the low range
Sets the distortion amount
Sets the input gain
Sets the tone of the input
Sets the frequency at which
pitch variation will occur
Sets the depth of pitch
variation
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
d: FB Amt
e: FB Amt
f: FB Amt
g: Feedback
The feedback output from Tap 1, 2, and 3 is mixed according
to the FB Amt, and then the final amount of feedback is
specified by Feedback.
Wet / Dry

062: Auto Reverse

This effect records the input signal and automatically plays
it in reverse (the effect is similar to a tape reverse sound).
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Right
D
a Rec Mode
Reverse Time
b
[msec]
Envelope
Select
c
Src
d Threshold
e Response
f Direct Mix
Wet/Dry
g Src
Amt
a: Rec Mode
b: Reverse Time [msec]
When Rec Mode is set to Single, you can set up to 2,640msec
for Reverse Time. If recording starts during the reverse
playback, the playback will be interrupted.
When Rec Mode is set to Multi, you can make another
recording during the reverse playback. However, the
maximum Reverse Time is limited to 1,320msec.
If you wish to record a phrase or rhythm pattern, set Rec
Mode to Single. If you record only one note, set Rec Mode
to Multi.
The Reverse Time parameter specifies the maximum
duration of the reverse playback. The part in excess of this
limit will not be played in reverse. If you wish to add short
pieces of the reverse playback of single notes, make the
Reverse Time shorter.
Direct
Auto Reverse
Mix
Rec/Reverse Play
Control
D-mod
-mod
Envelope Control
Input
Envelope Select
Single, Multi Sets the recording mode p.480
Sets the maximum duration of
20...2640
the reverse playback
Selects whether the start and
D-mod, end of recording is controlled
Input via the modulation source or
the input signal level
Selects the modulation source
that controls recording when
Off...Tempo
Envelope Select is set to D-mod
Sets the recording start level
0...100 when Envelope Select is set to
Input
Sets the speed of the response
0...100
to the end of recording
Always On,
Selects how a dry sound is
Always Off,
mixed
Cross Fade
Dry, 1 : 99... Sets the balance between the
99 : 1, Wet effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Wet / Dry
Wet / Dry
p.480
p.481
p.481
p.481
p.468
p.468