Modulation And Pitch Shift (Mod; 038: Stereo Vibrato - Korg M3 Parameter Manual

Modulation and Pitch Shift (Mod./P.Shift)

038: Stereo Vibrato

This effect causes the pitch of the input signal to shimmer.
Using the AutoFade allows you to increase or decrease the
shimmering speed.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sine LFO Shape
AutoFade Fade-In Delay
AUTOFADE Selects the modulation source
a Off...Tempo
Src that starts AutoFade
Fade-In Sets the fade-in delay time
00...2000
Delay [msec]
b
Sets the rate of fade-in
Fade-In Rate 1...100
LFO Triangle,
Selects the LFO Waveform
Waveform Sine
c
Changes the curvature of the
LFO Shape –100...+100
LFO Waveform
LFO Switches between D-mod and
D-mod,
d Frequency AUTOFADE for the LFO
AUTOFADE
Mod frequency modulation
LFO
Frequency 0.02...20.00 Sets the speed of the LFO
[Hz]
e Selects a modulation source for
Src Off...Tempo
LFO speed
–20.00... Sets the modulation amount of
Amt
+20.00 LFO speed
When this is on, the LFO speed
is set by BPM, Base Note, and
MIDI Sync Off, On
Times, instead of Frequency
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM 40.00...
f
manually for this individual
300.00
effect
Selects the type of notes that
Base Note ...
specify the LFO speed
Sets the number of notes that
Times x1...x32
specify the LFO speed
Individual, Selects either (individual) LFO,
LFO Type Common1, Common FX LFO1, or Common
Common2 LFO2
g
Sets the phase offset when
CmnLFO
–180...+180 Type = Common 1 or Common
Offset [deg]
2
Sets the depth of LFO
Depth 0...100
modulation
Selects the modulation source
h Src Off...Tempo
of the LFO modulation depth
Sets the modulation amount of
Amt –100...+100
the LFO modulation depth
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
i Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
Wet / Dry
Vibrato
Vibrato
Wet / Dry
LFO Frequency
p.465
p.465
p.465
p.449
p.465
p.448
p.448
p.448
p.448
p.448
p.448
Modulation and Pitch Shift (Mod./P.Shift)
a: AUTOFADE Src
b: Fade-In Delay [msec]
b: Fade-In Rate
d: LFO Frequency Mod
When LFO Frequency Mod is set to AUTOFADE, you can
use the modulation source selected in AUTOFADE Src as a
trigger to automatically fade in the modulation amount.
When MIDI Sync is set to On, you cannot use this.
The Fade-In Rate parameter specifies the rate of fade-in. The
Fade-In Delay parameter determines the time from
AutoFade modulation source On until the fade-in starts.
The following is an example of fade-in where the LFO
speed is increased from "1.0Hz" to "4.0Hz" when a note-
on message is received.
AUTOFADE Src=Gate1, LFO Frequency Mod=AUTOFADE,
LFO Frequency [Hz]=1.0, Amt=3.0
The effect is off when a value for the dynamic
modulation source specified for the AUTOFADE Src
parameter is smaller than 64, and the effect is on when
the value is 64 or higher. The AutoFade function is
triggered when the value changes from 63 or smaller to
64 or higher.
Gate1 Signal
Note On
Fade-In Rate
AUTOFADE
Fade-In Dealy
AutoFade
AUTOFADE
Source=Gate1
LFO Freq. Mod=AUTOFADE
LFO Frequency[Hz]=1.0
Amount=+3.0
All Note Off
LFO Frequency
=1.0+3.0=4.0Hz
LFO Frequency
=1.0Hz
465