Korg M3 Parameter Manual page 137

Module & GE Name
This indicates the module (M, A, B, C, D) selected by
Module Control.
This name is the name of the GE selected for each KARMA
module. The exception is that this will indicate Master only
if Master is selected.
Scene
This indicates the currently selected scene.
Chord Name
This shows the name of the chord detected for the KARMA
Module specified by the Module Control setting.
If "M" Master is selected, the chord for the last of the
Modules in operation will be displayed. (In other words, if
Modules A, B and C are running, the chord for Module C
will be displayed.)
Note: Chord detection is affected by the key zone (Combi 7–
1–1b) and Transpose (Combi 7–3b: Module Parameter-
Control) of each KARMA Module, and by the Dynamic
MIDI Destination (Combi 7–8) Chord Scan and Smart Scan
settings.
Selected Switch/Slider
This indicates the KARMA Sliders 1–8 or KARMA Switches
1–8 that is currently being operated or was operated most
recently.
Control Timbre Category Name
This indicates the category of the program used by the
timbre that is being played from the KARMA Module.
This will indicate Multi if a single KARMA Module is
playing multiple timbres of differing categories.
Realtime Control Name
This shows the full name of the realtime control that is
currently being operated or was operated most recently.
Module ID
Indicates which parameters you are controlling from the
KARMA Sliders or KARMA Switches.
A, B, C, D: Indicates the KARMA Module that is being
controlled. In this case, you are controlling a GE Real-Time
Parameter.
P: Indicates that the slider or switch is controlling a
Performance Real-Time Parameter.
Parameter No.
When Module ID is A,B,C or D (KARMA Module), this area
indicates the GE Real-Time Parameter number 01–32 that
you are controlling (see "7–2–1: GE RTP (GE Real-Time
Parameters)" on page 90).
If Module ID is P, this area indicates the Performance Real-
Time Parameter number 01–08 (see "7–2–2: Perf RTP (Perf
Real-Time Parameters)" on page 91) that you are controlling.
Parameter Value
This area indicates the value of the GE Real-Time Parameter
or Performance Real-Time Parameter you are controlling.
The value will change as you move the slider or operate the
switch.
A slider or switch can have multiple parameters
assigned to it. A maximum of four assigned parameters
can be displayed here in the available space. If there are
more, they will not be displayed (but a ">" will be
added to the end of the line). They will still function
when the control is activated, but you cannot view their
values directly.
0–6c: Realtime Controls
This displays the names and settings of KARMA Sliders 1–8
and KARMA Switches 1–8.
1, 2, 3, 4, 5, 6, 7, 8:
This shows the current settings of KARMA Switches 1–8
and the KARMA Sliders. The explanation below will
mention only Switch 1 and Slider 1. Switches 2–8 and Sliders
2–8 are the same as 1.
KARMA Switch1
This shows the current KARMA Switch 1 setting.
If Control Assign is KARMA, you can use the control
surface switches and sliders to control KARMA Switches 1–
8 and KARMA Sliders 1–8. You can also operate them by
directly pressing the switch shown in the display.
KARMA Switch1 Stored Value
This shows the setting of KARMA Switch 1 that is written
into the program.
KARMA Switch1 Name
[SW1...8, SL1...8]
This shows the name of KARMA Switch 1 (abbreviated
name).
You can assign this name in "7–4–3b: CAT., Names" on
page 175.
KARMA Slider1
This shows the current setting of KARMA Slider 1.
This shows the current setting of KARMA Slider 1. If
Control Assign is KARMA, this is linked with operations of
control surface slider 1. In addition, you can directly press
the slider shown in the display and then use the VALUE
slider, q/u switches, or VALUE dial to adjust the value.
KARMA Slider1 Stored Value
This shows the setting of KARMA Slider 1 that is written
[A...D, P]
into the program.
KARMA Slider Name
This shows the name of KARMA Slider 1 (abbreviated
name).
You can assign this name in "7–4–3b: CAT., Names" on
page 175.
▼0–6: Menu Command
[01...32]
• 0: Write Combination ☞p.185
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy from Program ☞p.185
• 4: Copy X–Y Motion ☞p.107
• 5: Copy KARMA Module ☞p.188
• 6: Initialize KARMA Module ☞p.189
• 7: Copy Scene ☞p.115
• 8: Swap Scene ☞p.115
• 9: Capture Random Seed ☞p.116
• 10: Auto Assign RTC Name ☞p.117
For more information, please see "Combination: Menu
Command" on page 185.
COMBI P0: Play 0–6: KARMA RTC
127