Korg M3 Parameter Manual page 43

OSC1 Center Volume
This sets the volume of Oscillator 1 at the center of the X
axis. It applies only when Equal Power, above, is set to Off.
The volumes at the extreme ends of the X axis are fixed. At
the left side, Osc 1 is always at 100% volume; at the right
side, Osc 1 is always at 0%.
OSC2 Center Volume
This sets the volume of Oscillator 2 at the center of the X
axis.
The volumes at the extreme ends of the X axis are fixed, in
the opposite direction of Oscillator 1's. At the left side, Osc 2
is always at 0% volume; at the right side, Osc 2 is always at
100%.
Osc Center Volume and X-Axis Position
100%
Volume 50%
0%
–127
Vector X-axis position
Center Volume Values:
X–Y Mortion
X–Y MODE
MIDI In
Scale
PROG P1: Basic/DT/Ctrls (Basic/Drum Track/Controllers) 1–5: X–Y Setup
[0, 25, 50, 75, 100%]
[0, 25, 50, 75, 100%]
0 +127
100
75
50
25
0
X–Y CC MIDI Output
Global Controllers
MIDI CC Assignments
Defaults: X=118, Y=119
X–Y CC Control
X Mode and
Y Mode
X–Y Volume Control
Osc 1/2 Center Volume
and Equal Power settings
1–5b: X–Y CC Control
X–Y CC control lets you use movements of the X–Y position
in X–Y MODE (or X–Y Motion) as an AMS source to control
the parameters of a program or as a Dmod source to control
an effect.
Each of the four directions of the X–Y can send a different
CC, including left (–X), right (+X), up (+Y), and down (–Y).
You can choose between several different patterns
combining these four directions by using the X Mode and Y
Mode parameters.
The X–Y CC is transmitted as MIDI control change messages
on the global MIDI channel. This means that it controls all
voices of the program, not individual voices.
Note: A Global parameter allows you to enable or disable
MIDI output for the CC Control. By default, this is disabled.
This setting does not affect the internal Programs, which can
always receive the X–Y CCs.
Enable CC Control
When this box is checked, the X–Y position will control the
CCs assigned to +X, –X, +Y, and –Y, as set below.
When this box is not checked, the CC assigned to +X, –X, +Y,
and –Y will have no effect. The MIDI CC# specified by
Global settings X (X–Y Mode) and Y (X–Y Mode) (P2:
Controllers – MIDI CC# Assign) will be transmitted and
received. For more information, please see "X–Y control and
MIDI" on page 32.
X Mode [Positive, Negative, Xfade, Split]
You can set up the X–Y CC control to send out CCs in
several different patterns, as shown in the graphic below.
This controls the pattern for the X axis. Note that this setting
affects only CC Control; it has no effect on Volume Control.
Positive sends out only +X, starting at 0 at the far left, and
increasing to 127 at the far right. –X is disabled in this mode.
Negative sends out only –X, starting at 0 at the far left, and
increasing to 127 at the far right. In this mode, +X is grayed
out.
Global switch (P1: MIDI):
"X–Y MIDI Out"
X–Y MODE
X–Y CC Control
X+/– and Y+/–
CC Assignments
Program switch:
"Enable CC control"
Program switch:
"Enable Volume control"
[Off, On]
X–Y CC MIDI Output
X–Y CC Modulation of
Program and FX Parameters
X–Y Modulation of
Oscillator Volume
33