103: Comp - P4Eq (Compressor - Parametric 4-Band Eq); 104: Comp - Cho/Flng (Compressor - Chorus/Flanger) - Korg Krome Parameter Manual

Mono-Mono Serial (Mono-Mono) 103: Comp - P4EQ (Compressor - Parametric 4-Band EQ)
103: Comp - P4EQ (Compressor -
Parametric 4-Band EQ)
This effect combines a mono compressor and a four‐band
parametric equalizer. You can change the order of the
effects.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a 1...100 Sets the sensitivity
Sensitivity
[C]Attack 1...100 Sets the attack level
b
Sets the compressor output level
Output Level 0...100
p.251
P4EQ
Sets the parametric EQ input
c [E]Trim 0...100
level
[E]B1 Cutoff Sets the center frequency of
20...1.00k
[Hz] Band 1
d Sets the bandwidth of Band 1
Q 0.5...10.0
Gain [dB] –18...+18 Sets the gain of Band 1
[E]B2 Cutoff Sets the center frequency of
50...5.00k
[Hz] Band 2
e Sets the bandwidth of Band 2
Q 0.5...10.0
Gain [dB] –18...+18 Sets the gain of Band 2
[E]B3 Cutoff Sets the center frequency of
300...10.00k
[Hz] Band 3
f Sets the bandwidth of Band 3
Q 0.5...10.0
Gain [dB] –18...+18 Sets the gain of Band 3
[E]B4 Cutoff Sets the center frequency of
500...20.00k
[Hz] Band 4
g Sets the bandwidth of Band 4
Q 0.5...10.0
Gain [dB] –18...+18 Sets the gain of Band 4
CompP4EQ, Switches the order of the
h Routing
P4EQ Comp compressor and parametric EQ
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
i Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
Wet / Dry
Routing
Parametric 4Band EQ
Trim
Wet / Dry
p.251
p.251
p.255
p.255
p.255
p.255
104: Comp - Cho/Flng
(Compressor - Chorus/Flanger)
This effect combines a mono compressor and a chorus/
flanger. You can change the order of the effects.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a
1...100 Sets the sensitivity
Sensitivity
[C]Attack 1...100 Sets the attack level
b
Sets the compressor output level
Output Level 0...100
p.251
c [C]EQ Trim 0...100 Sets the EQ input level
[C]Pre LEQ
–15...+15 Sets the gain of Low EQ
Gain [dB]
d
Pre HEQ Gain
–15...+15 Sets the gain of High EQ
[dB]
CHORUS/FLANGER
[F]LFO
Frequency 0.02...20.00 Sets the speed of the LFO
[Hz]
e
LFO
Triangle, Sine Selects the LFO Waveform
Waveform
[F]Delay Time
0.0...1350.0 Sets the delay time
[msec]
Sets the depth of LFO
f Depth 0...100
modulation
Sets the feedback amount
Feedback –100...+100
–Wet... Sets the effect balance of the
[F]Cho/Flng
–1 : 99, Dry, chorus/flanger
Wet/Dry
1 : 99...Wet
g
Selects the Wet/Dry modulation
Src Off...Tempo
source for the chorus/flanger
Sets the Wet/Dry modulation
Amt –100...+100
amount for the chorus/flanger
[F]Output Normal, Selects the output mode for the
h
Mode Wet Invert chorus/flanger
Comp
Switches the order of the
Flanger,
i Routing compressor and chorus/flanger
Flanger
Comp
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
j
Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
h: [F]Output Mode
i: Routing
When Wet Invert is selected, the right channel phase of the
chorus/flanger effect sound is inverted. This creates pseudo‐
stereo effects and adds spread.
However, if a mono‐input type effect is connected after this
effect, the left and right sounds may cancel each other,
eliminating the chorus/flanger effects.
When Routing is set to Flanger→Comp, [F]Output Mode
will be set to Normal.
Wet / Dry
Routing
Chorus/Flanger
Chorus/Flanger
Normal
+ Output Mode
–
Wet Invert
Feedback
Cho/Flng Wet / Dry
Wet / Dry
LFO: Tri / Sine
p.251
p.251
p.272
p.259, p.272
p.305
p.305
305