Oki IP-6620 Maintenance Manual page 180

Panel Message
PH TEMP IS TOO HIGH
PRINT? OK/CANCEL
COOLING PRINT HEADS
XXXX CC nn
XXXX: Print mode
cc: Print density
nn: Print direction
<Communication-related errors>
Panel Message
NO DATA RECEIVED
CHECK CONNECTION
DATA COMMUNICATION
WAS INTERRUPTED
<Other errors>
Panel Message
CLOSE COVERS
PLEASE WARM THE ROOM
AND WAIT FOR A WHILE
ROOM TEMP TOO HIGH
PRINT? OK/CANCEL
DECREASE ROOM TEMP
XXXX CC nn
XXXX: Print mode
cc: Print density
nn: Print direction
Chapter 5 Troubleshooting (Engine Section and USB Controller Section)
Error Description User Solution
The print heads - Restart the printer.
temperature is not - Check the ambient
within the operating temperature.
range (high
temperature).
The monitored - Restart the printer.
temperature of the - Check the ambient
print heads exceeded temperature.
40°C.
Error Description User Solution
An error has been - Replace the USB
detected in the USB cable.
connection during print - Restart the printer
data transfer. and the computer.
A timeout error has - Replace the USB
occurred during print cable.
data transfer. - Restart the printer
and the computer.
Error Description User Solution
The front cover is - Close the front
open. cover.
- Restart the printer.
The ambient - Restart the printer.
temperature is not - Check the ambient
within the printer temperature.
operating range (low
temperature).
The ambient - Restart the printer.
temperature is not - Check the ambient
within the printer temperature.
operating range (high
temperature).
The ambient - Restart the printer.
temperature is not - Check the ambient
within the printer temperature.
operating range (high
temperature).
OKI Data Infotech Corporation CONFIDENTIAL
Service Engineer Inspection
(For inspection criteria, see
Reference to Check/Replace
Parts.)
- Check the COOLINGFAN,MW
operation in the ACTUATORS
menu.
- Check that the COOLING
FAN,MW connectors are
connected correctly.
- Check that the CARRIAGE
FFC,MW connectors are
connected correctly to both the
HCB1M and the IPB5.
- Check that the HEAD
CABLE,MW connectors are
connected correctly.
- Check the COOLINGFAN,MW
operation in the ACTUATORS
menu.
- Check that the COOLING
FAN,MW connectors are
connected correctly.
- Check that the CARRIAGE
FFC,MW connectors are
connected correctly to both the
HCB1M and the IPB5.
- Check that the HEAD
CABLE,MW connectors are
connected correctly.
Service Engineer Inspection
(For inspection criteria, see
Reference to Check/Replace
Parts.)
Install the last firmware version.
Install the last firmware version.
Service Engineer Inspection
(For inspection criteria, see
Reference to Check/Replace
Parts.)
Check that the interlock switch
connectors are connected
correctly.
- Install the last firmware version.
- Check that the ambient
temperature thermistor cable is
not damaged or broken, and that
it is connected correctly.
- Install the last firmware version.
- Check that the ambient
temperature thermistor cable is
not damaged or broken, and that
it is connected correctly.
- Install the last firmware version.
- Check that the ambient
temperature thermistor cable is
not damaged or broken, and that
it is connected correctly.
Reference to
Assumed
Check/Replace
Replacement Part
Parts
- COOLING FAN,MW
- PCB-ASSY-HCB1M
- CARRIAGE FFC,MW
- HEAD CABLE,MW
- COOLING FAN,MW
- PCB-ASSY-HCB1M
- CARRIAGE FFC,MW
- HEAD CABLE,MW
Reference to
Assumed
Check/Replace
Replacement Part
Parts
- Firmware version
- PCB-ASSY-IPB5-100
- Firmware version
- PCB-ASSY-IPB5-100
Reference to
Assumed
Check/Replace
Replacement Part
Parts
- Window sensor OKI
Data Infotech
- PCB-ASSY-ACT3
- Firmware version
- Ambient temperature
thermistor
- PCB-ASSY-ACT3
- PCB-ASSY-IPB5-100
- Firmware version
- Ambient temperature
thermistor
- PCB-ASSY-ACT3
- PCB-ASSY-IPB5-100
- Firmware version
- Ambient temperature
thermistor
- PCB-ASSY-ACT3
- PCB-ASSY-IPB5-100
5-21