Oki IP-6620 Maintenance Manual page 176

Panel Message
<CIS model>
(With the ink box cover closed)
CC INK HAS RUN OUT
OPEN INK BOX COVER
CC: Ink color
<CIS model>
(With the ink box cover open)
REPLACE CC CARTRIDGE
CC: Ink color
<LCIS model>
(With the reservoir drawer closed)
CC INK HAS RUN OUT
OPEN THE DRAWER
CC: Ink color
<LCIS model>
(When you have opened the
reservoir drawer)
SUPPLY INK AND
CLOSE THE DRAWER
CC: Ink color
<CIS model>
(With the ink box cover closed)
WRONG COLOR FOR CC
OPEN INK BOX COVER
CC: Ink color
<CIS model>
(With the ink box cover open)
INK COLOR ERROR
CHECK CC CARTRIDGE
CC: Ink color
<CIS model>
(With the ink box cover closed)
INCORRCT CC INK TYPE
OPEN INK BOX COVER
CC: Ink color
<CIS model>
(With the ink box cover open)
CARTRIDGE TYPE ERROR
CHECK CC CARTRIDGE
CC: Ink color
Chapter 5 Troubleshooting (Engine Section and USB Controller Section)
Error Description User Solution
Ink has run out. - Reinstall the ink
cartridge.
- Replace the ink
cartridge.
Ink has run out. Supply ink to the
reservoirs.
There is a mistake with - Reinstall the ink
the ink cartridge color. cartridge.
- Replace the ink
cartridge with the
correct color.
There is a mistake with - Reinstall the ink
the ink cartridge type. cartridge.
- Replace the ink
cartridge with a
genuine cartridge.
OKI Data Infotech Corporation CONFIDENTIAL
Service Engineer Inspection
(For inspection criteria, see
Reference to Check/Replace
Parts.)
- Check the condition of the ink
supply pump tubes.
- Check the supply pumps
operation in the ACTUATORS
menu.
- Check the subtank full sensors
operation in the MONITOR
menu.
- Check that the subtank full
sensors connectors are
connected correctly.
- Check the subtank empty
sensors operation in the
MONITOR menu.
- Check that the subtank empty
sensors connectors are
connected correctly.
- Check the conditions of the ink
supply pump tubes.
- Check the supply pumps
operation in the ACTUATORS
menu.
- Check the subtank full sensors
operation in the MONITOR
menu.
- Check that the subtank full
sensors connectors are
connected correctly.
- Check the subtank empty
sensors operation in the
MONITOR menu.
- Check that the subtank empty
sensors connectors are
connected correctly.
- Install the last firmware version.
- Check that the ink chip is
recognized in the MONITOR
menu.
- Check that the pin on the
PCB-ASSY-INK4 is not soiled or
damaged.
- Check that the PCB-ASSY-INK4
connectors are connected
correctly.
- Check that the PCB-ASSY-ACT3
connectors are connected
correctly.
- Check that the
CABLE(Cartridge)-ASSY(MW) is
correctly connected and not
damaged.
- Check that the guide pin is not
damaged.
- Install the last firmware version.
- Check that the ink chip is
recognized in the MONITOR
menu.
- Check that the pin on the
PCB-ASSY-INK4 is not soiled or
damaged.
- Check that the PCB-ASSY-INK4
connectors are connected
correctly.
- Check that the PCB-ASSY-ACT3
connectors are connected
correctly.
- Check that the
CABLE(Cartridge)-ASSY(MW) is
correctly connected and not
damaged.
- Check that the guide pin is not
damaged.
Reference to
Assumed
Check/Replace
Replacement Part
Parts
- SUPPLY PUMP
TUBE,MW
- Subtank Sensor(OKI
Data Infotech)
- PCB-ASSY-ACT3
- CABLE(SubTank1-
IF)-ASSY(MW)
- CABLE(SubTank2-
IF)-ASSY(MW)
- CABLE(SubTank1)-
ASSY(MW)
- CABLE(SubTank2)-
ASSY(MW)
- CABLE(SubTank3)-
ASSY(MW)
- SUPPLY PUMP
TUBE,MW
- Subtank Sensor(OKI
Data Infotech)
- PCB-ASSY-ACT3
- CABLE(SubTank1-
IF)-ASSY(MW)
- CABLE(SubTank2-
IF)-ASSY(MW)
- CABLE(SubTank1)-
ASSY(MW)
- CABLE(SubTank2)-
ASSY(MW)
- CABLE(SubTank3)-
ASSY(MW)
- Firmware version
- PCB-ASSY-INK4
- PCB-ASSY-ACT3
- CABLE(Cartridge)-
ASSY(MW)
- Firmware version
- PCB-ASSY-INK4
- PCB-ASSY-ACT3
- CABLE(Cartridge)-
ASSY(MW)
5-17