Agilent Technologies InfiniiVision 3000 Programmer's Manual page 1220

Index
DIGital<d> commands, 281
digitize channels, 191
DIGitize command, 56, 61, 926
digits, 150
disable front panel, 822
disable function, 1011
disabling calibration, 248
disabling channel display, 258
disabling status register bits, 158,
discontinued and obsolete commands,
display annotation, 291
display annotation background, 292
display annotation color, 293
display annotation text, 294
display channel labels, 297
display clear, 295
DISPlay commands, 289
display commands introduction, 290
display connect, 1006
display date, 819
display factors scaling, 263
display for channels, 258
display frequency span, 319
display measurements, 388, 420
display order, 1007
display persistence, 299
display reference, 834, 836
display reference waveforms, 988
display reset conditions, 169, 825
display serial number, 212
display vectors, 300
display wave position, 1007
display, lister, 361
display, measurement statistics on/off,
display, oscilloscope, 283, 299, 317, 503,
display, serial decode bus, 598
displaying a baseline, 853
displaying unsynchronized signal,
divide math function, 310, 331
DNS IP, 48
domain, 48
domain, network printer, 351
driver, printer, 1016
DSO models, 6
duplicate mnemonics, 1093
duration, 887, 888, 891
duration for glitch trigger, 874, 875,
duration of power analysis, 543
duration qualifier, trigger, 887, 888
duration triggering, 844
duty cycle measurement, 57, 388,
Duty Cycle, power modulation analysis,
dV/dt slew rate, 552
E
EBURst trigger commands, 861
ECL channel threshold, 1002
ECL threshold voltage for digital channels,
ECL trigger threshold voltage, 1044
edge activity, 1000
edge counter, Edge Then Edge trigger,
1220
edge counter, Nth edge of burst,
edge coupling,
edge fall time,
edge parameter for delay measurement,
edge preshoot measured,
edge rise time,
EDGE SEARch commands,
edge search slope,
172 edge search source,
995 edge slope, 870
edge source, 871
edge string for OR'ed edge trigger,
EDGE trigger commands,
edge triggering,
edges (activity) on digital channels,
edges in measurement,
efficiency, 453
efficiency power analysis, apply,
elapsed time in mask test,
ellipsis, 150
enable channel labels,
enabling calibration,
enabling channel display,
enabling status register bits, 158,
end of string (EOS) terminator,
end of text (EOT) terminator,
end or identify (EOI),
energy loss, 454
EOI (end or identify),
EOS (end of string) terminator,
EOT (end of text) terminator,
erase data, 295
erase measurements,
424 erase screen, 1008
820 error counter (ARINC 429),
error counter (ARINC 429), reset,
error frame count (CAN),
853 error frame count (UART),
error messages, 821,
error number,
error queue, 821,
error, measurement,
ESB (Event Status Bit), 173,
ESE (Standard Event Status Enable
Register), 158,
ESR (Standard Event Status Register), 160,
879 1065
ETE demo signal,
event status conditions occurred,
Event Status Enable Register (ESE), 158,
401 Event Status Register (ESR), 160, 216,
529 example code, :ACQuire:COMPlete,
example code, :ACQuire:SEGMented,
example code, :ACQuire:TYPE,
example code, :AUToscale,
example code, :CHANnel<n>:LABel,
example code, :CHANnel<n>:PROBe,
example code, :CHANnel<n>:RANGe,
example code, :DIGitize,
287
example code, :DISPlay:DATA,
example code, :DISPlay:LABel,
example code, :DISPlay:ORDer,
858
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
862
867
402
399
413
418
748
749
750
882
866
844
183
397
512
480
297
248
258
172
1090
1090
1090
1090
1090
1090
1018
604
605
620
727
1047
821
1067
388
175
1066
275
175
1066
1065
221
227
232
186
261
263
269
192
296
297
1007
example code, :MEASure:PERiod,
example code, :MEASure:RESults,
example code, :MEASure:TEDGe,
example code, :MTESt, 469
example code, :POD<n>:THReshold,
example code, :RUN/:STOP, 211
example code, :SYSTem:SETup, 828
example code, :TIMebase:DELay,
example code, :TIMebase:MODE,
example code, :TIMebase:RANGe,
example code, :TIMebase:REFerence,
example code, :TRIGger:MODE,
example code, :TRIGger:SLOPe,
example code, :TRIGger:SOURce,
example code, :VIEW and :BLANk,
example code, :WAVeform, 946
example code, :WAVeform:DATA,
example code, :WAVeform:POINts,
example code, :WAVeform:PREamble,
example code, :WAVeform:SEGMented,
example code, *RST, 170
example programs, 6, 1097
EXE (Execution Error) status bit, 158,
execution error detected in Standard Event
Status, 160
exponential fall waveform generator
output, 971
exponential math function, 311,
exponential notation, 149
exponential rise waveform generator
output, 971
extended video triggering license,
external glitch trigger source, 880
external range, 304
external trigger, 301, 303, 871
EXTernal trigger commands, 301
EXTernal trigger level, 868
external trigger probe attenuation factor,
external trigger probe sensing, 1009
EXTernal trigger source, 871
external trigger units, 305
F
fail count, current harmonics analysis,
fail/pass status (overall) for current harmonics
analysis, 522
failed waveforms in mask test, 478
failure, self test, 177
fall time measurement, 388, 402
Fall Time, power modulation analysis,
falling edge count measurement,
falling pulse count measurement,
Fast Fourier Transform (FFT) functions, 310,
318, 319, 321, 1010
FF values in waveform data, 933
FFT (Fast Fourier Transform) functions, 310,
318, 319, 321, 1010
FFT (Fast Fourier Transform) operation, 331,
945
FFT vertical units, 320
fifty ohm impedance, disable setting,
422
415
430
505
1043
833
835
836
851
870
871
217
933
937
941
227
160
331
913
303
517
529
404
405
827