Page 4
In Case of Difficulty ........................1-42 Shipping Damage or Incorrect Shipment................1-42 Network, System Administration, or Test Server Help ............1-42 Optional Agilent Performance Port Actuator Control System (ACS)......... 1-42 Vacuum Subsystem......................1-42 Additional Resources ......................1-42 MS Windows System Installation Reference In this Chapter..........................
This system should only be installed by an Agilent 3070 service-trained customer engineer (CE). Testhead boot conflicts may occur if this system is on a network with 3070 UNIX controllers with IP addresses other than in the 10.3.112.XX series. Configuring the System to a Network page 1-22 for more information.
Typically, the Agilent 3070 Site Preparation Manual (03066-90114) is delivered to the customer by an For 3070 systems, the label on the lower right corner of Agilent representative one month prior to system the rear of the testhead cradle identifies the module shipment.
Only, 1-19 Attach the Site LAN Cable, 1-20 Install the Footswitch NOTE With software revision 3070 05.20p and later, the Footswitch Cable coiled Testhead Leveling Foot footswitch must be connected to the system. The under front of testhead footswitch must be pressed to lock fixtures on the testhead.
Systems (shipped in paper with the system). NOTE If you are setting up a network with other UNIX- based 3070 systems, be aware that the IP address of 3070 UNIX systems changed from the HP 15.3.112.XX series to the Agilent 10.3.112.XX series.
Page 35
3070service identified by the button label number on the button. test credit buttons: Click Start > Programs > Agilent 3070 > PPU Report? A report similar to the one shown in Figure 1-12 page 1-30 will be displayed in a new window.
1-18). 1 Shut down the testhead. Also install floor brackets to keep the testhead stable. If you don’t have a floor bracket kit, order Agilent 2 Rotate the testhead to the normal position, then 44990-63221. Installation instructions accompany install the shipping bolts to keep it from being rotated the kit.
3 Start DGN if it does not start automatically: Testhead a Open a Korn shell window: Boot the Testhead, 1-33 One way is to click Start > Programs > Agilent Troubleshooting Testhead Boot, 1-33 3070 > Korn Shell. Check the System Config...
See the Agilent 3070 / 79000 Repair Manual. NOTE For more information about see “The Root Directory $AGILENT3070_ROOT, Environment Variable” in Chapter 2.
NOTE 2 Start Diagnostics if it does not start automatically: Do not press Save Config as that will make the a Click Start > Programs > Agilent 3070 > Korn Manual Intervention selection permanent. Shell. b At the Korn Shell window prompt, enter: 3 Run Full Diagnostics.
1-18 for the location of a Fill Out the System Support Log leveling foot. Introduce the customer to the Agilent 3070 / 79000 System Support Log, 03066-90150. NOTE It may be necessary to remove the pod cover to 1 Place your business card in Chapter 1, and suggest access the hex-slot of the leveling foot.
Chapter 1: MS Windows System Installation Procedure: Completing the Installation 2 Place the customer's Agilent 3070 software licenses Installing the system and completing full in Chapter 2. Diagnostics – four hours. 3 Fill out the Installation and Configuration Records to Contact EMTD at 1.800.447.TEST to bill charges above...
User documentation shipped on the controller’s hard drive. Optional Agilent Performance Port Actuator Control System (ACS) See Agilent Performance Port in the 3070 Service Documentation. Vacuum Subsystem See “Air Subsystems” troubleshooting in the online service documentation.
Files, 2-35 Introduction The bootptab File, 2-36 The information in this chapter may be helpful when The hosts File, 2-38 installing an Agilent 3070 system that has a MS Windows controller. Device Files, 2-40 Vacuum Control, 2-41 Rotating the Testhead, 2-42...
Environment Variable, 2-3 Double-click the desktop Korn Shell icon OR Use of the Root Directory Environment Variable in Click Start > Programs > Agilent 3070 > Korn a BT-BASIC Window, 2-4 Shell. Use of the Root Directory Environment Variable in...
"C:/Agilent3070/diagnostics/th1/ get btgetenv$ ("AGILENT3070_ROOT") & config" config" "/diagnostics/th1/config" NOTE At software revision 3070 05.00p, the Agilent3070 directory was moved from D:/Agilent3070/ C:/Agilent3070/ is only required for BT-BASIC commands which are referenced to the root. btgetenv$ ("AGILENT3070_ROOT") If the BT-BASIC command is used prior to the next BT-BASIC command (for example msi btgetenv$ ("AGILENT3070_ROOT") &...
The directory to which statistics are logged. $AGILENT3070_ROOT/qm A directory that contains templates used throughout the system. $AGILENT3070_ROOT/standard A directory that is used by the 3070 software for storing temporary files / $AGILENT3070_ROOT/tmp logs. A directory that is used for storing a few utility files.
(/) for commands tied to Korn Shell Quick Reference on page 2-17. a 3070 application, and use a back-slash (\) for operating system-related commands. vi and vi Editor Quick Reference on page 2-20.
Chapter 2: MS Windows System Installation Reference: Korn Shell Quick Reference NOTE Korn Shell Quick Although the operating system is MS Windows, a If uncertain whether to use front-slashes or number of 3070 UNIX commands are valid in the Korn back-slashes, see Front-Slashes versus Reference shell.
-l the factory and normally do not require adjustment. c If errors are returned, the board config will not The capabilities of a 3070 system are based on the compile properly. codewords and software licenses installed. Compile the Two Config Files Codeword &...
Page 81
Functional Description: Enables the testing of digital devices through series resistors using Agilent TestJet drivethru technology. You can use the Agilent Drive Thru Test in combination with the Agilent Access Consultant to identify and selectively remove nonessential probing locations. Allows Agilent SimPlate Express or cassette fixtures for your board test. If this express fixturing option is not enabled, only an Agilent SimPlate Fixture can be used.
Chapter 2: MS Windows System Installation Reference: Vacuum Control Vacuum Control Location of Vacuum Control Statements See the Agilent 3070 / 79000 Family Site Preparation Manual 03066-90114 for a drawing of this default These are contained in the system config file: vacuum hookup.