Agilent Technologies InfiniiVision 3000 Programmer's Manual page 1218

Index
baud rate, 626, 687, 725
begin acquisition, 191, 211, 213
BHARris window for minimal spectral
leakage, 321
binary block data, 150, 296, 828,
BINary waveform data format, 589
bind levels for masks, 494
bit order, 726
bit order, SPI decode, 706
bit selection command, bus, 235
bit weights, 160
bitmap display, 296
bits in Service Request Enable Register,
bits in Standard Event Status Enable
Register, 158
bits in Status Byte Register, 175
bits selection command, bus, 236
blank, 190
block data, 150, 163, 828
block response data, 64
blocking synchronization, 1079
blocking wait, 1078
BMP format screen image data,
braces, 149
built-in measurements, 57
burst data demo signal, 274
burst width measurement, 393
burst, minimum time before next,
bus bit selection command, 235
bus bits selection commands, 236
bus clear command, 238
bus commands, 234
BUS data format, 930
bus display, 239
bus label command, 240
bus mask command, 241
BUS<n> commands, 233
button disable, 822
button, calibration protect, 248
byte format for data transfer, 929,
BYTeorder, 931
C
C, SICL library example, 1178
C, VISA library example, 1131
C#, SCPI.NET example, 1198
C#, VISA COM example, 1107
C#, VISA example, 1150
CAL PROTECT button, 248
CAL PROTECT switch, 243
calculating preshoot of waveform,
calculating the waveform overshoot,
calibrate, 245, 246, 248, 252
CALibrate commands, 243
calibrate date, 245
calibrate introduction, 243
calibrate label, 246
calibrate output, 247
calibrate start, 249
calibrate status, 250
calibrate switch, 248
1218
calibrate temperature,
calibrate time,
CAN acknowledge,
CAN and LIN demo signal,
933 CAN baud rate,
CAN demo signal,
CAN frame counters, reset,
CAN SEARch commands,
CAN serial bus commands,
CAN serial search, data,
CAN serial search, data length,
CAN serial search, ID,
173 CAN serial search, ID mode,
CAN serial search, mode,
CAN signal definition,
CAN source,
CAN trigger, 629,
CAN trigger data pattern,
CAN trigger ID pattern,
CAN trigger pattern id mode,
CAN triggering,
capture data,
296 capturing data,
cardiac waveform generator output,
center frequency set, 310,
center of screen,
center reference,
863 center screen, vertical value at, 330,
channel, 217, 261, 1000,
channel coupling,
channel display,
channel input impedance,
channel inversion,
channel label, 261,
channel labels, 297,
channel numbers,
channel overload,
channel protection,
channel reset conditions, 168,
935 channel selected to produce trigger, 880,
channel signal type,
channel skew for oscilloscope probe, 266,
1003
channel status, 214,
channel threshold,
channel vernier,
channel, stop displaying,
CHANnel<n> commands, 253,
channels to autoscale,
channels, how autoscale affects,
characters to display,
chart logic bus state math function, 311,
413
chart logic bus state, clock edge,
407
chart logic bus state, clock source,
chart logic bus timing math function, 311,
chart logic bus, units,
chart logic bus, value for data = 0,
chart logic bus, value for data increment,
classes of input signals,
classifications, command,
clear, 295
clear bus command,
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
251
252
625
276
626
275
622
774
618
776
777
778
779
775
627
628
632
631
633
634
595
191
56
972
318
958
836
334
1002
257
258
259
260
1001
298
1007
268
268
824
912
267
1007
1002
272
190
255
188
185
820
331
313
312
331
316
315
314
321
1088
238
clear cumulative edge variables,
clear markers, 394, 1018
clear measurement, 394, 1018
clear message queue, 157
Clear method, 59
clear reference waveforms, 987
clear screen, 1008
clear status, 157
clear waveform area, 290
clipped high waveform data value,
clipped low waveform data value,
clock, 675, 707, 710
clock slope, I2S, 658
CLOCk source, I2S, 660
clock source, setup and hold trigger,
clock timeout, SPI, 708
clock with infrequent glitch demo signal,
CLS (Clear Status), 157
CME (Command Error) status bit, 158,
CMOS threshold voltage for digital
channels, 287, 1002
CMOS trigger threshold voltage,
code, :ACQuire:COMPlete, 221
code, :ACQuire:SEGMented, 227
code, :ACQuire:TYPE, 232
code, :AUToscale, 186
code, :CHANnel<n>:LABel, 261
code, :CHANnel<n>:PROBe, 263
code, :CHANnel<n>:RANGe, 269
code, :DIGitize, 192
code, :DISPlay:DATA, 296
code, :DISPlay:LABel, 297
code, :DISPlay:ORDer, 1007
code, :MEASure:PERiod, 422
code, :MEASure:RESults, 415
code, :MEASure:TEDGe, 430
code, :MTESt, 469
code, :POD<n>:THReshold, 505
code, :RUN/:STOP, 211
code, :SYSTem:SETup, 828
code, :TIMebase:DELay, 1043
code, :TIMebase:MODE, 833
code, :TIMebase:RANGe, 835
code, :TIMebase:REFerence, 836
code, :TRIGger:MODE, 851
code, :TRIGger:SLOPe, 870
code, :TRIGger:SOURce, 871
code, :VIEW and :BLANk, 217
code, :WAVeform, 946
code, :WAVeform:DATA, 933
code, :WAVeform:POINts, 937
code, :WAVeform:PREamble, 941
code, :WAVeform:SEGMented, 227
code, *RST, 170
code, SCPI.NET library example in C#,
code, SCPI.NET library example in
IronPython, 1210
code, SCPI.NET library example in Visual Basic
.NET, 1204
code, SICL library example in C, 1178
code, SICL library example in Visual
Basic, 1187
1000
933
933
899
274
160
1044
1198