General Descriptions For Pm Procedure - Toshiba e-STUDIO 2555C Service Manual

In addition, when the developer unit is recognized as a new one by the M developer unit old/new
detection switch, or the auto-toner sensor adjustment is performed, the counter is also reset.
• 08-5574: Current value of PM counter [developer material (C)]
• 08-5575: Current value of PM time counter [developer material (C)]
When the current value of "DEVELOPMENT UNIT" on the main screen or "CYAN DEVELOPER (C)"
on the sub-screen in the PM support mode is cleared, the counter is reset.
In addition, when the developer unit is recognized as a new one by the C developer unit old/new
detection switch, or the auto-toner sensor adjustment is performed, the counter is also reset.
• 08-5576: Current value of PM counter [parts other than the PM parts of the process unit]
• 08-5577: Current value of PM time counter [parts other than the PM parts of the process unit]
When the current value of "2nd TRANSFER" on the main screen or "2nd TRANSFER ROLLER" on
the sub screen in the PM support mode is cleared, the counter is reset.
7.3

General Descriptions for PM Procedure

(1) Preparation
• Ask the user about the current conditions of the equipment and note them down.
• Before starting maintenance, make some sample copies and store them.
• See the replacement record and check the parts to be replaced in the PM support mode (6S)
or list printing mode (9S-103).
6S : [6] + [START] + [POWER] ON
9S-103 : [9] + [START] + [POWER] ON → [103] → [START]
PM SUPPORT CODE LIST
2012-04-09 13:16
UNIT
DRUM(K)
DRUM BLADE(K)
GRID(K)
MAIN CHARGER NEEDLE(K)
CHARGER CLEANING PAD(K)
DRUM(Y)
DRUM BLADE(Y)
GRID(Y)
MAIN CHARGER NEEDLE(Y)
CHARGER CLEANING PAD(Y)
DRUM(M)
DRUM BLADE(M)
GRID(M)
MAIN CHARGER NEEDLE(M)
CHARGER CLEANING PAD(M)
DRUM(C)
DRUM BLADE(C)
GRID(C)
MAIN CHARGER NEEDLE(C)
CHARGER CLEANING PAD(C)
• Turn OFF the power and make sure to unplug the equipment.
(2) Perform a preventive maintenance using the following checklist and illustrations. Refer to the
Service Manual if necessary.
(3) Plug in the equipment after the maintenance has been finished. Then turn ON the power and
make some copies to confirm that the equipment is working properly.
© 2012-2013 TOSHIBA TEC CORPORATION All rights reserved
S/N : CYL000001 FIN S/N : FIN S/N-xxxxxxxx
TOSHIBA e-STUDIOxxxx
OUTPUT PAGES PM OUTPUT PAGES DRIVE COUNTS
DEVELOP COUNTS DEVELOP COUNTS
1957 1957
1957 1957
1957 1957
1957 1957
1957 1957
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
1077 1077
Fig. 7-1
7 - 5
TOTAL : 2146
DF TOTAL : 1213
PM DRIVE COUNTS
3940 170000
10870 170000
10870 170000
10870 170000
10870 170000
3766 170000
3766 170000
3766 170000
3766 170000
3766 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
9547 170000
e-STUDIO2555C/3055C/3555C/4555C/5055C
PREVENTIVE MAINTENANCE (PM)
7