Sharp IV-C35M User Manual page 340

Computer Link
*1 When the termination code is 08
appended information. (Example: 0A
*2 Measurement number when outputting the results
00 = Measurement 0, Camera 1, 01
(H)
03 = Measurement 2, 04
(H)
*3 Result output (Y0 to Y15)
Bit
Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
*4 Measurement program for measurement 0
00 = none, 01
(H)
*5 Measurement programs for measurements 1 to 4
00 = none, 01
(H)
lead inspection, 04
06 = object counting by binary conversion, 07
(H)
= point measurement, 09
inspections, 0B
0E = color positional measurement.
(H)
*6 Output data from measurements 0 to 4 (block 0)
The data output will vary according to whether "ANY" or "BLOCK-ASSIGN" was selected on the
SERIAL OUTPUT item. - Pages 21-25 to 21-29.
When a block is specified
- The measurement data from measurement numbers 0 to 4 in block 0 is output. (Max. 496
bytes).
- Measurement numbers that have not been specified will not output any data. (The space will
be filled by the next item. Max. 500 bytes.)
- See pages 23-6 to 23-17, for details about the measurement data in block 0.
When "ANY" is selected for the output
See page 23-18.
*7 Assigned block data
When the SERIAL OUTPUT item is set to "BLOCK-ASSIGN," the IV-C35M will output the
measurement result data in the specified block number. When the SERIAL OUTPUT item is set
to "ANY," the nature of the output will depend on the output settings.
For details about how to specify measurement output, see pages 21-25 and 21-27.
- No data is output if block 0 (00) is specified.
For details about the measurement data block, see pages 23-5 to 23-17.
- The top address where the specified block of data is written will be an address made by
adding 512 bytes to the top address for writing results.
Top address
for writing
results
Top address
for writing
results
23
+ 512 bytes
= Measurement 3, 05
(H)
H (09005)
7 6 5 4 3 2 1 0
= positional deviation measurement
(H)
= positional deviation measurement, 02
(H)
= BGA/CSP inspection, 05
(H)
= multiple positional measurement, 0A
(H)
= fault inspection, 0C
(H)
Sharp Mitsubishi
09000
D0000
09001
. .
. .
. .
.
.
.
.
.
.
. .
. .
. .
19000
D0256
19001
. .
. .
. .
(received an error response), the error code is contained in the
(H)
on a Sharp PC = parity error)
(H)
= Measurement 0, Camera 2, 02
(H)
= Measurement 4
(H)
L (09004)
7 6 5 4 3 2 1 0
Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
(H)
= area measurement by binary conversion,
(H)
= object identification by binary conversion, 08
(H)
= color evaluation, 0D
(H)
Yokogawa
OMRON
L L
L
DM0000 D00001
H H
H
. .
. .
. .
L L
L
. .
. .
H H
H
. .
. .
. .
L L
L
DM0256
D00257
H H
H
.
.
.
.
.
.
23-4
= Measurement 1,
(H)
= degree of match inspection, 03
= multiple degree of match
(H)
= color unevenness inspection,
(H)
Contents
Termination code
Appended information
.
.
.
Output data from
measurement 4 (block 0) .
.
.
.
Assigned block data
.
.
.
.
=
(H)
(H)