Sharp IV-C35M User Manual page 20

Setting and Operating Outline
Details of each item on the menu bar
1
Item on the menu bar
MAIN-COND
(main conditions)
CHG-MEA
(Change measurement)
COND-CHG
(Change the
measurement
conditions)
CHNG-REG
(change registration)
SCREEN-CHG
(change screen)
CHG-TYPE
(change the object
type)
NEXT-NG *
(change the NG image)
CHG-C1
(change the Camera 1
image position)
CHG-C2
(change the Camera 2
image position)
MANL-MEAS
(Manual measurement)
SHORTCUT
Description
Displays the MAIN screen.
Press the up and down arrow keys to change the display of
the evaluation results for each measurement number.
(Measurement 0 camera 1 -> measurement 0 camera 2 ->
Measurement 1 -> Measurement 2 -> Measurement 3 ->
Measurement 4)
Displays the condition change selection list. Change the
conditions that get displayed by pressing the up and down
arrow keys.
Change the display of the set of stored details between [A00]
to [A07] and [A08] to [A15] using the up and down arrow keys
Displays the screen change selection list. Select a screen
using the up and down arrow keys.
Note: The OPS-MAIN, JDG-COND-CHG,and PC-MNTR do
not appear on the popup menu unless "YES" is selected.
for each corresponding item on "TYPE RUN COND"
menu. Only the currently available screens are listed.
When an NG image is stored, "NG-IMG-DISP" can be
selected. Press the SET key and the monitor will change to
the NG image display screen.
- See page 1-22 in this manual
Displays the object type selection list.
Select an object type by pressing the up and down keys.
This is enabled when Manual Object Type Change is set to
"YES."
List the NG screens that can be selected.
Select a screen using the up and down keys.
Moves the image from Camera 1 up and down the screen
using the up and down arrow keys.
Note: This is enabled when "CAM1&2" or "CAM1&NG IMG" is
selected in 1MONITOR OUTPUT on the TYPE RUN
COND menu (operating conditions).
Moves the image from Camera 2 up and down the screen
using the up and down arrow keys.
Note: This is enabled when "CAM1&2" or "CAM1&NG IMG" is
selected in 1MONITOR OUTPUT on the TYPE RUN
COND (operation conditions).
Manually move the two crosshair cursors, and measure
distance between these two points, as well as coordinate
distance on X and Y axes.
Note: Unless "MANL-MEAS" is selected on the
"qEXTENSION FUNC" line in the TYPE RUN COND
(operation conditions), this screen cannot be displayed.
Displays a short cut screen.
1-12
Display detail on the screen
IVC35M
SYS-CND
OBJECT TYPE COND
SET WIZARD
EDIT MAIN OPS MENU
OPTION
ENVIRONMENT SETTING
MEMORY CARD
MEASURE0 CAM1 NO
This part changes.
MEA-CND
DST&ANG COND...
NUMERIC CALC
COND-CHG CHNG-REG
A0= A08=
to to
A07 A07
2 2
OPS-MAIN
PC-MNTR
PC-MNTR 2
SCREEN-CHG CHG-TYPE
(TYPE00)
This part changes.
MANL-MEAS
1CURSOR1-COORD MOVE(224.208)
2CURSOR2-COORD MOVE(287.271)
DIST-BETW-2PT 089.0
DIST-BETW-X 063.0
DIST-BETW-Y 063.0
PLACE
1SHORTCUT1
NO
2SHORTCUT2
NO
3SHORTCUT3
NO