0-3: Mix (Mixer) - Korg MICROX X50 Parameter Manual

0–2d: Selected Timbre Information
This shows information on the timbre (1–8) that is currently
selected for editing.
Timbre No.: Bank No., Prog No.: and name
This shows the timbre number, and the program bank, num-
ber and name selected for that timbre.
Status
This shows the MIDI and internal tone generator status for
each track.
Ch
This shows the MIDI channel number specified for the tim-
bre.
■ 0–2: UTILITY
☞"Write Combination," "Solo Selected Timbre" (0–1)
Select by Category
(Combi/Category, Prog T1...T8/Category)
Combinations or the programs used by each timbre can be
selected by category.
If you have selected "Combi Select," selecting Utility "Select
by Category" will access the Combi/Category dialog box,
allowing you to select a combination by category. (☞p.35)
If you have selected "Program Select," selecting Utility
"Select by Category" will access the Prog T1...T8/Category
dialog box, allowing you to select a program for each timbre
by category.
For the procedure of selecting by category, refer to p.2.
0–3: Mix
(Mixer)
Here you can set the pan and volume for each timbre 1–8.
0–3a
0–3a: Pan, Volume
Pan
Sets the pan for each timbre 1–8.
L001...C064...R127: A setting of L001 is far left and R127 is
far right. A setting of C064 will reproduce the pan setting
that was made for the oscillator in Program mode.
36
(INT, Off, EXT, EX2)
(01...16, Gch)
[RND, L001...C064...R127]
OSC1 OSC2
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center Right
OSC1
OSC2
OSC1: Amp1 Pan=C064
OSC2: Amp2 Pan=C064
Left Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center Right
If a mono-type insertion effect is inserted, the setting you
make here will be ignored. In this case, the "Pan (CC#8)"
parameter in 8: Ed–InsertFX, Setup page will adjust the pan-
ning of the sound after the insertion effect (☞p.99 "3.
Mixer").
RND: The oscillator pan will change randomly at each note-
on.
If "Status" (2–1a) has been set to INT, MIDI control
change #10 (panpot) messages can be received to con-
trol the setting. CC#10 values of 0 or 1 will place the
sound at far left, 64 at center, and 127 at far right.
Pan can be controlled by messages received on the
"MIDI Channel" (2–1a).
This parameter can also be set from the 1: Ed–Tone Adjust,
Mixer page.
Volume
Adjusts the volume of each timbre 1–8.
The volume of each timbre is determined by summing
this volume value with the MIDI volume (CC#7) and
expression (CC#11). If "Status" (2–1a) has been set to
INT, incoming MIDI CC#7 or CC#11 messages will con-
trol the volume of a timbre. (However these messages
will not affect the setting of this parameter.)
If "Status" is EXT or EX2, the value of this parameter
will be transmitted as MIDI CC#7 when the combina-
tion is changed. However this will not be transmitted
by a timbre that is set to the same MIDI channel as the
global MIDI channel. This message is transmitted on
the "MIDI Channel" (2–1a) specified for each timbre.
This parameter can also be set from the 1: Ed–Tone Adjust,
Mixer page.
■ 0–3: UTILITY
☞"Write Combination," "Solo Selected Timbre" (0–1),
"Select by Category" (0–1, PROG 0–1)
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Left Center Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left Center
Right
[000...127]