Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Yamaha CRW4260t-B
Summary of Contents for Yamaha CRW4260t-B
- Page 1 CRW4260t SERIES User Guide Guide de I’utilisateur Bedienungsanleitung...
- Page 2 If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center Court, San Jose, CA95112, U.S.A.
- Page 3 Laser Diode Properties Material : GaAlAs Wavelength : 782-789 nm Emission Duration : Continuous Laser Output Power : Less than 44.6 W* his output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT...
- Page 4 WARNING • The temperature where CRW4260t is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4260t cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4260t.
- Page 5 • Do not subject the CRW4260t and computer to impact or shock when in use, as this may impair recording or playback. • Yamaha is not responsible for any data or infor- mation losses resulting from the operation of the CRW4260t.
-
Page 6: Table Of Contents
This document may not, in whole or in part, be copied, photocopied, reproduced, translated, transmitted or reduced to any electronic medium of machine readable form without prior consent in writing from Yamaha. MS-DOS and Windows are registered trademarks of Microsoft, Inc. -
Page 7: Introduction
Introduction Introduction Thank you for purchasing a Yamaha CRW4260t drive. Please read this manual before using the drive in order to make the best use of the supe- rior CRW4260t functions. After reading, please retain this manual for future reference. -
Page 8: Orange Book Compatible Recording
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CD-ROM drives other than a CD-RW or CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). -
Page 9: Chapter 1 - System Configuration
Note: You will need about twice as much space on your hard disk as that required by the data you wish to write to CD-ROM. SCSI card This is required in order to connect a SCSI device (the Yamaha CRW4260t) to your computer. We recommend the following: Adaptec SCSI cards: AHA-2940 (PCI), AHA-284x (VL), AHA-2740 (EISA), AHA-154x (ISA), etc. -
Page 10: Tools
On the CRW4260t, you can use conventional CD-RW and CD-R discs that conform to the Recordable Compact Disc Systems Part 2 and Part 3 (Orange Book). Yamaha recommends the following Yamaha CD-RW and CD-R discs: CD-RW Discs > CRWM74R CD-R Discs >... -
Page 11: Chapter 2 - Installing The Yamaha Crw4260T Chapter 2 - Drive
Chapter 2 - Installing the Yamaha CRW4260t Drive Chapter 2 - Installing the Yamaha CRW4260t Drive CRW4260t drive settings Before installing the CRW4260t in your computer, you will need to set the following jumpers. You set these jumpers by inserting jumper connectors into the jumper switch located on the rear panel of the CD-RW drive. - Page 12 Chapter 2 - Installing the Yamaha CRW4260t Drive Note: When you are using Windows 95, and if the SCSI ID setting on the rear panel is the same as the number assigned to another SCSI device, the Plug and Play component of Windows 95 will automatically assign an unused number to the CRW4260t (SCAM protocol level 1).
- Page 13 Chapter 2 - Installing the Yamaha CRW4260t Drive Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON (with a jumper) — Use this setting if the CRW4260t is the last device in the internal SCSI daisy-chain.
-
Page 14: Installing The Crw4260T Drive
Chapter 2 - Installing the Yamaha CRW4260t Drive Installing the CRW4260t drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. - Page 15 Chapter 2 - Installing the Yamaha CRW4260t Drive 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Remove the SCSI card, and set the terminator setting of the SCSI internal circuit to the position for internal connected devices.
- Page 16 Chapter 2 - Installing the Yamaha CRW4260t Drive 8. Connect the AUDIO cable. Connect the single 4-pin connector (Sound Blaster compatible) to the sound card. Connect the 4-pin connector at the other end of the cable (the larger connector) to the AUDIO OUT connector on the CRW4260t drive.
- Page 17 Chapter 2 - Installing the Yamaha CRW4260t Drive 9. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW4260t drive. The shape of the connector makes it impossible to reverse the connections.
- Page 18 Chapter 2 - Installing the Yamaha CRW4260t Drive 12. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4260t drive is lit. 13. Start up your operating system.
-
Page 19: Chapter 3 - Operation
Chapter 3 - Operation Front Panel 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. -
Page 20: Loading A Disc
Chapter 3 - Operation Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the disc tray softly or press the eject button again to close the disc tray. -
Page 21: Ejecting The Disc
Chapter 3 - Operation Ejecting the Disc If the CRW4260t is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject opera- tion while the CRW4260t is reading data. Caution: Be sure to remove the disc after it is completely ejected. -
Page 22: Manual Eject (Emergency Use)
Chapter 3 - Operation Manual Eject (emergency use) Here we explain how to eject the disc when it cannot be ejected in the normal way; for example, the power is shut off inadvertently or the loading mechanism fails. This technique should be used only as a last resort. -
Page 23: Troubleshooting
Troubleshooting If CRW4260t is not performing as expected, look up the symptoms in the following table, and take the appropriate corrective action. Symptoms The power to the CRW4260t is off The power to the computer is off The CRW4260t is not recognized by the computer The CRW4260t does not operate correctly... -
Page 24: Appendix
Appendix Specifications Interface Data Capacity Record/Read Speed Data Transfer Rate Burst Transfer Rate Buffer Size Access Speed Installation Disc Loading Audio Out (normal speed) Power Consumption Power Supply Environment Dimensions (WxHxD) Weight Rear Panel SCSI/Power Supply ID Selector Audio Out Specifications are subject to change without prior notice. -
Page 25: Front Panel Indicator Key
Front Panel Indicator Key on: green on: orange Status Reset Ready (no disc) Inserting disc Ejecting disc Ready (disc inserted) Seeking Preparing to write Writing Writing (test mode) Playback flashing: green — off flashing: orange ON/DISC Read/Write — Appendix — —... - Page 26 French: Pour plus de détails sur les produits, veuillez vous adresser à Yamaha ou au distributeur le plus proche figurant dans la liste suivante : German: Bei weiteren Fragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden Firmen.