Tractor Stop; Engine Stop - Belarus 2022.6 Operator's Manual

ATTENTION: IT IS NECESSARY TO PRESS CLUTCH PEDAL QUICKLY AND RE-
LEASE SLOWLY, LITTLE BY LITTLE. THIS FACILITATES PRECISE GEAR SHIFTING AND
BREAKAWAY. SLOWLY AND NON-FULLY PRESSING OF CLUTCH PEDAL LEADS TO
CLUTCH SLEEPING AND CAUSES DIFFICULT AND NOISY GEARS SHIFTING IN GEAR
BOX. IF CLUTCH PEDAL IS RELEASED QUICKLY, THE LOAD ON TRANSMISSION IN-
CREASES AND TRACTOR MOVES JERKILY. WHEN RELEASING CLUTCH PEDAL, IT IS
NECESSARY TO TAKE OFF FOOT FROM PEDAL AT THE END OF PEDAL TRAVEL, to
REGENERATE PLAY IN HYDRAULIC DRIVE OF CLUTCH CONTROL.
ATTENTION: WHEN STARTING TO MOVE, MAKE SURE THE PARKING BRAKE IS
DISENGAGED!
ATTENTION: WITH THE DIFFERENTIAL LOCK ENGAGED, THE SPEED OF TRAC-
TOR MOVEMENT SHALL NOT EXCEED 13 KM/H!
ATTENTION: OPERATING ON ROADS WITH HARD SURFACE, IT IS NECESSARY
TO SWITCH OFF THE FDA DRIVE TO AVOID INCREASED WEAR OF FRONT WHEEL
TIRES!
ATTENTION: IT IS ALLOWED TO USE THE ENGINE AT ITS FULL POWER ONLY
AS THE COOLANT TEMPERATURE REACHES 70°C!
ATTENTION: TRACTOR OPERATION WITH EMPTY ADBLUE (UREA) TANK IS NOT
ALLOWED! WHEN INFORMATION ABOUT THE CRITICAL LEVEL OF ADBLUE REAGENT
(UREA) IN THE TANK APPEARS ON THE MONITOR, IT IS NECESSARY TO FILL THE
TANK WITH ADBLUE REAGENT.
ATTENTION: IT IS NOT RECOMMENDED TO LET ADBLUE FREEZING AND OVER-
HEATING, AS IT SHORTENS ITS STORAGE LIFE. SCR SYSTEM PROVIDES NORMAL
OPERATING CHARACTERISTICS AT THE AMBIENT TEMPERATURE FROM -40 TO +40
ºС!

3.2.4 Tractor stop

To stop the tractor, do the following:
- decrease engine speed;
- fully depress the clutch pedal;
- stop the tractor with service brakes;
- set the GB range and gear shifting lever into neutral position;
- release the clutch and service brakes pedals;
- engage the parking brake.
ATTENTION: FOR TRACTOR EMERGENCY STOP, PRESS THE CLUTCH AND
BREAK PEDALS TOGETHER SHARPLY!

3.2.5 Engine stop

ATTENTION: BEFORE STOPPING THE ENGINE, LOWER LIFT LINKAGES UNTIL
THEY REACH THE GROUND, IF THEY ARE UPLIFTED; LET THE ENGINE RUN AT
(1000±100) RPM FOR 3 TO 5 MINUTES. THIS ALLOWS TO REDUCE ENGINE COOLANT
TEMPERATURE!
To stop the engine, do the following:
- set the rear PTO control lever into the position "off" and the handle for the rear PTO
drive activation – into the position "PTO drive off"' ;
- disengage the rear axle differential lock, the FDA drive, FPTO (if mounted);
- shift the control handles for the hydraulic lift linkage distribution valve group into neu-
tral position;
- set the lift linkage control handle into the position "off";
- turn off the conditioner;
- turn the key of the starter and instruments switch from the position "I" into the position
"0";
- deactivate the accumulator battery when the engine is stopped for a long time.
ATTENTION: AB SHALL BE SWITCHED OFF NOT EARLIER THAN TWO MIN-
UTES AFTER ENGINE STOP. THE GIVEN TIME PERIOD IS NECESSARY TO BLEED
SCR MODULES AND PIPELINES FROM AdBlue REAGENT AND TO CREATE INFOR-
MATION IN MEMORY MODULE OF ELECTRONIC CONTROL UNIT.
ATTENTION: FOR ENGINE EMERGENCY STOP, TURN THE KEY OF THE
STARTER AND INSTRUMENTS SWITCH FROM THE POSITION "I" INTO THE POSI-
TION "0"!
79
2022.6-0000010 OM