Belarus 2022.6 Operator's Manual page 40

Monitor buttons 1, 2, 3, 4, 5 (figure 2.9.1) are of multifunctional purpose. When pressing
any of buttons 2, 3, 4 during the monitor operation, an image of button panel 6 appears on the
screen, the icons denoting the current functions of each button. Pressing button 1 on the moni-
tor activates the main three-segment image on the screen. In this case an engine speed scale
is displayed in the upper left corner and a scale of oil pressure in the engine lubrication system
is displayed in the upper right corner, cooling fluid temperature - in the lower right corner, cur-
rent fuel flow per hour - in the lower left corner. When the three-segment imaging is indicated,
the displayed parameters in the lower left corner are chosen with button 1. To exit the mode of
choosing between the displayed parameters in the upper right corner it is required to press
button 5 after activation of the button panel 6. After that the parameters are chosen between
with buttons 1 and 2.
After calling up button panel 6, a four-segment imaging of parameters on screen 7 is
activated with button 2. After the first pressing button 2, four parameters are displayed in the
digital mode on the screen:
- in the upper left corner – engine speed;
- in the upper right corner – coolant temperature;
- in the lower left corner – on-board voltage;
- in the lower right corner – oil pressure in the lubrication system.
When pressing button 2 for the second and third time, four parameters are displayed on
the screen in an analog form.
Using the mode of choosing between the displayed parameters, the customer can acti-
vate if necessary displaying of various engine parameters on the screen according to table
2.9.1. The mode of parameter choosing is activated after calling up the button panel with
short-time pressing button 5. Successive pressing button 1 changes the parameters displayed
in the upper left corner, pressing button 2 changes the parameters in the upper right corner,
button 3 – in the lower left corner, button 4 – in the lower right corner. The parameter choosing
mode is exited with short-time pressing button 5.
After calling up the button panel by pressing button 3, menu of SCR system is acti-
vated.
Displaying of SCR system parameters and viewing of critical modes of SCR system
operation are given in subsection 2.27 "SCR system operation".
Such parameters of SCR as "AdBlue level in tank", ''AdBlue temperature in tank",
"temperature of exhaust gases before SCR catalyst" can be displayed without input to the
menu of SCR system parameters. Look-up of other SCR system parameters, indicated in table
2.9.1, is possible only through menu of SCR system parameters.
If you press button 3, when being in menu, graphical displaying of engine parameters in
course of time is activated (functions as a parameter analogue recorder). The required graphic
parameters are chosen with a successive pressing button 3 according to table 2.9.1.
A temporary net can be adjusted in a configuration menu from 2, 10 or 30 min. to 1, 2, 4
or 8 hours. To enter the configuration menu it is necessary to press button 5 and hold it
pressed for more than 3 sec. Also it is possible to choose metric and British units of measure-
ment in this menu, among available languages it is possible to choose English, Spanish, Swe-
dish, French, German, Italian, Dutch, Portuguese and Russian.
ATTENTION: ONLY DEALERS ARE AUTHORIZED TO CHANGE SETTINGS OF THE
CONFIGURATION MENU!
When errors (faults) are detected during the operation, the monitor produces a sound
signal and a rhombic flashing window with an exclamation mark appears on the screen.
After calling up the button panel, a list of active errors (faults) is invoked with button 4.
Moving over the list is carried out with buttons 1 and 2.
To exit displaying of the lift of active errors, it is necessary to confirm the reception of all
errors by pressing button 3. After the errors stop appearing on the display, they are automati-
cally deleted from the list.
40
2022.6-0000010 OM