Belarus 2022.6 Operator's Manual page 17

The hydraulic lift linkage is remote-cylinder, providing draft, position, combined and
depth adjustment for agricultural machinery position, and suppression of vertical oscillation
of agricultural implements in traveling position; with electrohydraulic system (EHR) of rear
lift linkage automatic control. The system has three pairs of independent outlets.
Free drain is available at the back for tractor operation with hydraulic units with con-
stant delivery, for example, with hydraulic motors.
The rear lift linkage is a three-point linkage of category 3 under ISO 730 and a link-
age 3 under GOST 10677. There are two cylinders Ц90x250.
Bushings are included into tractor SPTA to provide an opportunity for coupling of im-
plements of category 2 according to ISO 730 and lift linkage 2 according to 10677 to RLL.
The front lift linkage (against order) is a three-point linkage of category 2 under ISO
730 and a linkage 2 according to GOST 10677. There are two cylinders Ц90x250.
Drawbar hitches of a lift type:
- short towing yoke DH 2V – for coupling with semi-trailers and semi-trailed imple-
ments;
- long towing yoke DH 3V – for coupling with trailers and trailed implements;
- pin DH-2R ("Python") – for coupling with semi-trailers and semi-trailed machines
(against order);
- towing bar DH-1M-01 –for coupling with semi-trailed and trailed agricultural ma-
chines (against order);
- cross member DH-1 – for coupling with trailed and semi-trailed machines (against
order).
Drawbar hitches of a lift type, purchasing and mounting of which onto "BELARUS-
2022.6" tractors is allowed to be carried out by a customer individually, are as follows:
- automated yokes KU2000/329NB33 or KU5410/329-33 (manufactured by company
"Walterscheid") with a spherical pin – for coupling with trailers and semi-trailers, as well as
with agricultural machines based on trailers and semi-trailers;
- coupling device "python" PB5329NNB33 (manufactured by company "Walter-
scheid") – for coupling with agricultural machines having a tail piece with an ear on the
towing beam;
- ball coupling devices KI8329NB33 and KB8329NB33 (manufactured by company
"Walterscheid") – for coupling with agricultural machines having a tail piece with a spheri-
cal seat on the towing beam.
In coordination with "MTW", a customer is allowed to purchase and mount onto the
tractor an automated yoke, coupling device "python" and ball coupling device manufac-
tured by other companies if parameters and coupling dimensions of the above mentioned
devices correspond to parameters and coupling dimensions, specified in corresponding
tables 4.4.6, 4.4.7, 4.4.8, 4.4.9, 4.4.10 of subsection 4.4 "Drawbar hitches".
The cabin is a one-seated with a protective rigid framework, having thermal, noise
and vibration insulation, equipped with a sprung seat adjustable for operator's height and
weight, with rear-view mirrors, with a sun visor, with electrical wipers for front and rear
screens, with front and rear screen washers, with a roof lamp and a place to install a radio
set, with a system of air-conditioning and heating. Against order, the tractor can be
equipped with an additional seat. The cab doors have got locks, there are keys for the left
door. The right door is for emergency exit. The cab complies with category 2 under EN
15695-1:2009.
The electrical equipment complies with GOST 3940. The rated power supply voltage
for on-board network is 12V. The rated voltage for the start-up is 24V.
Instruments are a combination of devices; an integrated indicator; informational dis-
play; pilot lamps (glow lamps and light emitting diodes), located on the block of pilot lamps,
on the control panel of the rear axle differential lock and FDA drive, on the engine control
system board.
17
2022.6-0000010 OM