Enable On Led Keypad; Programming; Codes - Installers; Lost Installer Codes - Bentel Security KYO 320 Installation Manual

n Enable on LED Keypad
The "Enable LED keypad" table will allow you enable
the code concerned on the LED Keypads (16 keypads
max).
n Programming
Due to the extreme importance of Code functions (sys -
tem access and security), the programming procedure
is different from that normally used.
Full downloading of all the parameters on the User
page depends on whether or not the Code PIN entries
(entered at Computer) match the Control panel PINs
(programmed at the system Keypad). In the event of
mismatch, a dialogue box will inform you of the incon -
gruity:
<<WARNING: PINs in Control Panel not congruent.
Only data for Partition enabling, associated Timers and
Code Types will be sent>>.
If you select OK you will be able to program the De -
scription, Enabled Partitions, Associated Timers,
User menu access and Code Type ONLY.
If you wish to program the Code parameters (Available
status, Active status, Panic attribute, Patrol attribute
Father Codes and PIN), you must first upload the
Users page from the Control panel.
Matching Code entries All the programmed Code
data will be downloaded, including any user modified
parameters.
Mismatching Code entries Only the following param -
eters will be sent:
Ø Description
Ø Enabled Partitions Functions
Ø Associated Timer
Ø Code Type

Codes - Installers

The Installer Codes can access the system for pro -
gramming and maintenance purposes.
The MASTER Installer code is always Active and can
perform a limited number of programming and mainte -
nance operations.
The four Installer Codes can be made Activated as re -
quired, and programmed to perform a limited number of
programming and maintenance operations.
+
The Installer Code can program and change all pa -
rameters via computer.
The Installers page will allow you to program Installer
code attributes, as follows.
+
You cannot program an Installer Code without first
entering its Father Installer Code PIN.
KYO320
The Installer Code hierarchy is set at factory and
CANNOT be changed:
Ø Installer codes no. 196, 197, 198 and 199 have two
Father codes which cannot be changed: themselves
and Code no. 200;
Ø Code no. 200 is its own Father code and cannot be
changed.
The Table on the left side of the Installers page shows
the 5 Installer Codes . The page layout is as follows:
No. Refer to "No." in the "Keypad codes - Users" section.
Description Refer to "Description" in the "Keypad
codes - Users" section.
On the right side of the Installers page you can set the
parameters for the Codes selected on the left side of the
page, as described below.
Active Refer to "Active" in the "Keypad codes - Users"
section.
+
The Active status of Installer Code no. 200 is irre -
versible.
Father PIN Refer to "Father PIN" in the "Keypad
codes - Users" section.
+
At default the Installer Code PIN is 0 followed by
the Code ID Number. For KYO320 for example, the
PIN of Code no. 200 is 0200;
New PIN Refer to "New PIN" in the "Keypad
codes - Users" section.
Redigit New PIN Refer to "Redigit New PIN" in the
"Keypad codes - Users" section.
Code Type Refer to "Code Type" in the "Keypad
codes - Users" section.
+
The Installer Code type CANNOT be changed.
The Code Type for Installer Codes no. 196 and 197 is
Install. Type 1 and CANNOT be changed.
The Code Type for Installer Codes no. 198 and 199 is
Install. Type 2 and CANNOT be changed.
TheCode Type for Installer Codes no. 200 is a MASTER
and CANNOT be changed.
n Lost Installer Codes
For the instructions on how to restore the default PIN 0200
for KYO320, refer to the "Restore Default Settings" paragraph.
!
If the Installer Codes Lock option is enabled
(refer to "Options"), restoral of the default set -
tings WILL NOT restore the Installer Code PIN.
NOTE: If this occurs, contact your Service dealler.

PROGRAMMING

79