Input Configuration Menu - Extron electronics SMP 300 Series User Manual

Frame Rate (video)
Archive and confidence encodes have independent frame rate settings. This menu provides
a frame rate selection (frames per second) from the following list:
30 (default)
•
25
•
Frame rates are selected separately for the archive and confidence encoder configurations.
Bit Rate (Video)
Archive and confidence encodes have independent video bit rate settings. Video (VID) bit
rate sets a target video bit rate from 200 kbps to 10000 kbps (default 5000 kbps).
Rotate the left (
Bit Rate (Audio)
Archive and confidence encodes have the same audio bit rate settings. Audio (AUD) bit rate
allows the user to select an audio bit rate in kbps from the following selections:
• 80
• 192 (default)
Rotate the right (

Input Configuration Menu

This menu allows the user to configure each of the five inputs.
NOTE: The Input Configuration submenus are input specific. Depending on the
input type, not all submenus (shown in gray on subsequent pages) are available.
From the Input Config menu, press NEXT to enter the submenu (see image below, right).
Input Select
The first submenu is the input selection (see image above
right). Rotate either ADJUST knob to select the desired input
number from the active front panel input selections for further
configuration. This selection determines the subsequent
submenus that are visible.
Input Format
The next submenu selects the input signal format (see image
at right).
INPUT #1
*HDMI/DVI
*Default
**Input 5 is only available on the SDI models.
24
•
15
•
[
) ADJUST knob to select the video bit rate.
• 96
• 256
{
) ADJUST knob to select an audio bit rate.
INPUT #2 INPUT 3
*HDMI/DVI *YUVp/HDTV
Composite
12.5 10
• •
12 5
• •
• 128
• 320
NOTE: The Input Configuration submenus are input
NOTE: The Input Configuration submenus are input
specific. Depending on the input type, not all
specific. Depending on the input type, not all
submenus (shown in gray on subsequent pages)
submenus (shown in gray on subsequent pages)
are available.
are available.
INPUT 4
*HDMI/DVI
(3) H
YUVi
(3) TTLPIX
SMP 300 Series • Front Panel Operations
INPUT
MENU
INPUT
MENU
CONFIG
CONFIG
NEXT
NEXT
INPUT SELECT
INPUT SELECT
<3>
<3>
Rotate either to
Rotate either to
select input.
select input.
INPUT #[3]
INPUT #[3]
<YUVp/HDTV>
<YUVp/HDTV>
Rotate either to
Rotate either to
select the input format.
select the input format.
(3) H START V
(3) H START V
<128> <128>
<128> <128>
Rotate [ to select the horizontal
**INPUT 5
Rotate [ to select the horizontal
start pixel.
start pixel.
Rotate { to adjust the vertical
*Auto‑SDI
Rotate { to adjust the vertical
start pixel.
start pixel.
ACTIVE V
3G‑SDI
(3) H ACTIVE V
<1024> <0768>
<1024> <0768>
Rotate [ to adjust Horizontal Active pixel HD‑SDI
Rotate [ to adjust Horizontal Active pixel
width.
width.
Rotate { to adjust Vertical Active pixel height.
SDI
Rotate { to adjust Vertical Active pixel height.
PHASE
(3) TTLPIX PHASE
<XXX> <16>
<XXX> <16>
Rotate [ to adjust TTL pixel width.
Rotate [ to adjust TTL pixel width.
Rotate { to adjust phase.
Rotate { to adjust phase.
39
ASPECT RATIO IN[1]
ASPECT RATIO IN[1]
<FILL>
<FILL>
Rotate either to
Rotate either to
select an aspect ratio for the
select an aspect ratio for the