Input Configuration Menu - Extron electronics SMP 351 User Manual

Input Configuration Menu

This menu allows the user to configure each of the five inputs.
NOTE: The Input Configuration submenus are input specific. Depending on the input
type, not all submenus (shown in gray on subsequent pages) are available.
From the Input Config menu, press NEXT to enter
the submenu (see image at right).
Input Select
The first submenu is the input selection (see image
at right). Rotate either ADJUST knob to select the
desired input number from the active front panel input
selections for further configuration. This selection
determines the subsequent submenus that are visible.
Input format
The next submenu selects the input signal format (see image at
right).
INPUT #1
*HDMI
*Default
**Input 5 requires an optional 3G/HD/SDI input card.
NOTE: When there is no active input, the input parameters show "N/A". For digital
inputs, H/V start, H/V active, total pixel and phase submenus do not apply.
Film detection (interlaced input formats only)
Film detection is automatically enabled when an interlaced input format is selected (see
Input format above). Film detection supports 2:2 and 3:2 detection. The processing
maximizes image detail and sharpness for interlaced sources that originated from film. Film
detection is valid for any interlaced input type. The SMP 351 de-interlaces NTSC, PAL, and
1080i inputs.
If PIP mode and film detection are on for both inputs, the priority is given to the interlace
input. If both inputs are interlaced, priority is first to the larger window size, or to the main
window.
Film detection mode cannot be disabled and has no user adjustments.
INPUT #2 INPUT 3
*HDMI *YUVp/HDTV
YUVi
Composite
NOTE: The Input Configuration submenus are input
specific. Depending on the input type, not all
submenus (shown in gray on subsequent pages)
are available.
INPUT
NOTE: The Input Configuration submenus are input
CONFIG
specific. Depending on the input type, not all
submenus (shown in gray on subsequent pages)
Next
are available.
INPUT SELECT INPUT
<1>
CONFIG
Rotate either to Next
select input.
INPUT SELECT
INPUT #[3]
<1>
<AUTO DETECT>
Rotate either to
select input.
Rotate either to
select the input format.
INPUT #[3]
<AUTO DETECT>
(3) H START
<128> <128>
Rotate either to
select the input format.
Rotate
start pixel.
Rotate
INPUT 4 **INPUT 5
(3) H START start pixel.
<128> <128>
(3) H ACTIVE
*HDMI *Auto-SDI
<1024> <0768>
Rotate
3G-SDI
start pixel.
Rotate
Rotate
width.
HD-SDI start pixel.
Rotate
(3) H ACTIVE
SDI
(3) TTLPIX PHASE
<1024> <0768>
<XXX> <16>
Rotate
width.
Rotate
Rotate
Rotate
(3) TTLPIX PHASE
ASPECT RATIO IN[1] <XXX> <16>
<FILL>
Rotate
Rotate
Rotate either to
select an aspect ratio for the
selected input.
ASPECT RATIO IN[1]
EDID INPUT #[1] <FILL>
<720p_60_2ch>
Rotate either to
select an aspect ratio for the
Rotate
selected input.
EDID value for the
active input.
EDID INPUT #[1]
<720p_60_2ch>
IN[1] AUDIO SELECT
<LPCM 2CH>
Rotate
EDID value for the
Rotate either to
active input.
select an audio input source
for the selected input.
IN[1] AUDIO SELECT
IN[1] AUDIO LEVEL <LPCM 2CH>
<0 dB>
Rotate either to
select an audio input source
Rotate either to set the
for the selected input.
audio input level from -18
to +24 dB.
IN[1] AUDIO LEVEL
<0 dB>
Rotate either to set the
audio input level from -18
to +24 dB.
SMP 351 • Front Panel Operation
Menu
Menu
V
to select the horizontal
to adjust the vertical
V
V
to select the horizontal
to adjust Horizontal Active pixel
to adjust the vertical
to adjust Vertical Active pixel height.
V
to adjust Horizontal Active pixel
to adjust TTL pixel width.
to adjust Vertical Active pixel height.
to adjust phase.
to adjust TTL pixel width.
to adjust phase.
to set an
to set an
34