Extron electronics SMP 300 Series User Manual page 128

Command Function
IP Setup Commands (continued)
Set current port timeout
View current port
timeout
Set global IP port
timeout
View global IP port
timeout
X6(
KEY: = Port timeout
RS-232 Port
Configure serial port
parameters
Reset serial port
View serial port settings
Set serial port receive
timeout
View serial port receive
timeout
X1(
KEY: = Port timeout
X2)
= Intercharacter timeout Time in tens of milliseconds to wait between characters coming into a serial port before terminating
X2!
= Primary port status
X2@
= Length delimiter
X2%
= RS‑232 baud rate
X2^
= RS‑232 parity
X2&
= RS‑232 data bits
X2*
= RS‑232 stop bits
Front Panel Lock (Executive Mode)
Set Executive mode
View Executive mode
X5!
= Executive mode 0 = Off,
KEY:
RCP 101 Executive Mode
Executive mode on
Executive mode off
Query status
X(
KEY: = On/off
SIS Command
(Host to Device)
E X6( }
0 * TC
E }
0 TC
E X6( }
1* TC
E }
1 TC
In tens of seconds, zero padded 1 to 65000 (default: 00030 = 300 seconds)
E
X2% , X2^ , X2& , X2* }
1* CP
E }
1*9600,n,8,1CP
E }
1CP
E
X1( * X2) * X2@ * X2! }
1* CE
E }
1CE
Time in tens of milliseconds to wait for characters coming into a serial port before terminating
(min=0, max=32767, default: 10 = 100 ms). The response is returned with leading zeros.
(min=0, max=32767. Default: 2 = 20 ms). The response is returned with leading zeros. Commands using
X1( X2)
both and must have both values = 0 or both set to non‑zero.
Parameter to set either the Length of message to receive, or the Delimiter value.
#
L=
=byte count (min=0, max=32767. Default=0L=0 byte count).
D = decimal value for ASCII character. (min=0, max=00255. Default=00000L).
Value is placed prior to parameter: 3 byte length = "3L" and ASCII 0A delimiter is "10D". The parameter is
case sensitive, must use capital D or capital L. The response is returned with leading zeros.
Priority status for receiving timeouts:
1 Configure
receive timeout command parameters (default = 0).
= Use
9600 (default), 19200, 38400, 57600, 115200 baud
O E N
dd, ven, one (default),
7, 8 (default)
1 (default), 2
X5!
X
X
1 = Complete lockout (no front panel control),
99 * 1X
99 * 0X
99 * X
0 = Disabled/off (default),
Response
(Device to Host)
X6( ]
Pti 0 *
X6( ]
X6( ]
Pti1 *
X6( ]
X2% X2^ X2& X2*]
•
Cpn 01 Ccp , , ,
X2% X2^ X2& X2*]
Cpn 01 • Ccp , , ,
X2% X2^ X2& X2* ]
, , ,
• X1( X2) X2@ X2! ]
Cpn01 Cce , , ,
X1( X2) X2@ X2! ]
, , ,
0 = Use Send data string command parameters when available,
M S
ark, pace
X5!]
Exe
X5!]
2 = Menu lockout,
]
Exe99*1
]
Exe99 *0
X( ]
1 = Enabled/on
SMP 300 Series • Remote Communication and Control
Additional Description
3 = Allow recording controls only
120