Front Panel Menu Diagrams - Extron electronics SMP 300 Series User Manual

Front Panel Menu Diagrams

PICTURE
MENU MENU
PRESETS
CONTROL
NEXT NEXT
ARCHIVE ENCODER CHANNEL SELECT
RECALL <N/A>
<A> [ON]
Rotate either to Rotate either to select a
channel.
select a preset to recall.
ARCHIVE ENCODER
[A] H POSITION V
(For Composite mode only)
SAVE <N/A>
+0000 +0000
Rotate [ to adjust Horizontal
Rotate either to select
Position.
a preset # to save
current settings to. Rotate { to adjust Vertical Position.
[A] H SIZE V
(For Composite mode only)
IN<1> USER RECAL
<640> <480>
<N/A>
Rotate [ to adjust Horizontal Size.
Rotate [ to select an
Rotate { to adjust Vertical Size.
input.
Rotate { to select a preset.
[A] BRIGHT CONTRAST
IN<1> USER SAVE
<064> <064>
<N/A>
Rotate [ to adjust Brightness.
Rotate [ to select an
Rotate { to adjust Contrast.
input.
Rotate { to select a preset.
[A] COLOR TINT
<064> <064>
Rotate [ to select Color.
Rotate { to select Tint.
RECORD/STREAM
MENU
CONFIGURATION
NEXT
ENCODER ENCODER
-OR-
<CONFIDENCE>
<ARCHIVE>
Rotate either to Rotate either to
select encoder type. select encoder type.
NOTE: See the Record/Stream configuration
diagram on the following page.
(For Composite mode only)
INPUT BACKGROUND
MENU MENU
CONFIGURATION RECALL
NEXT NEXT
INPUT SELECT RECALL
<1> <back1080.png>
Rotate either to Rotate either to select.
select input. Press NEXT to load
the background file
and exit.
INPUT #[3]
<YUVp/HDTV>
Rotate either to
select the input format.
(3) H START V
<128> <128>
Rotate [ to select the horizontal
start pixel.
Rotate { to adjust the vertical
start pixel.
(3) H ACTIVE V
<1024> <0768>
Rotate [ to adjust Horizontal Active pixel
width.
Rotate { to adjust Vertical Active pixel height.
(3) TTLPIX PHASE
<XXX> <16>
Rotate [ to adjust TTL pixel width.
Rotate { to adjust phase.
ASPECT RATIO IN[1]
<FILL>
Rotate either to
select an aspect ratio for the
selected input.
EDID INPUT #[1]
<720p_60_2ch>
NOTE: The Input Configuration submenus are input
Rotate [ to set an
specific. Depending on the input type, not all
EDID value for the
submenus (shown in gray on subsequent pages)
active input.
are available.
IN[1] AUDIO SELECT
<LPCH 2CH>
Rotate either to
select an audio input source
for the selected input.
IN[1] AUDIO LEVEL
<0 dB>
Rotate either to set the
audio input level from -18
to +24 dB.
ADVANCED VIEW COMM
MENU
MENU
SETTINGS
CONFIGURATION
Press and hold
NEXT
INPUT 5 + NEXT
for 3 seconds.
IN<1> AUTO IMAGE "Hidden" Menu*
OFF
EDIT COMM
SETTINGS
Rotate [ to select input.
Rotate { to toggle on or off.
PREVIEW HDMI OUT
SERIAL PORT
<1280X720@60Hz>
9600 RS232
Rotate either to select a
Rotate either to
resolution.
change baud rate.
MAC ADRESS
AUTO MEMORY
005A6078CEC
<ON>
This is set at the factory and
Rotate { to toggle
cannot be changed.
Auto Memory
(Skipped in "Edit" mode.)
On or Off.
DHCP MODE
<OFF> On
TEST PATTERN
<N/A>
Rotate either to toggle
DHCP mode On or Off.
Rotate either to select a
test pattern.
IP ADDR
192.168.254.254
RECORD DRIVE LIMITER
Rotate [ to select octet field.
<NOT RESTRICTED>
Rotate { to change address.
Rotate either to select
the drive restriction. SUBNET
255.255.000.000
Rotate either to change mask.
RESET
<NONE>
Rotate either to
GATEWAY
reboot or reset unit
000.000.000.000
configurations.
Rotate [ to select octet field.
Rotate { to change address.
SMP 300 Series • Reference Information
STATUS
NEXT
ALARM STATUS
[NONE, HDCP, VIDEO...]
ARCHIVE
[...FILENAME...]
DRIVE SPACE INT
[FREE/TOTAL][GB]
DRIVE SPACE [USB]
[FREE/TOTAL] [GB]
SELECTED VOLNAME
[FREE/TOTAL][GB]
[ARCH] BR 5000kpbs
MULTI TS/RTP
CONF BR 350 kpbs
UNI RTP/UDP
160