BRP Evinrude E-Tec Series Service Manual page 424

INDEX
Gearcase Alignment Kit, P/N 5007231 310
Hydraulic Cylinder Rod Holder,
P/N 983213 382, 383
Injector Test Fitting Kit, P/N 5005844 184
Large Puller Jaws, P/N 432129 246, 326,
347, 350
Lifting Eye, P/N 321537 S–17
Lifting Tool, P/N 342672 240, 262
Lower Driveshaft Puller, P/N 342681 319
Lower Driveshaft Spline Tool,
P/N 5007052 316, 336
Lower Driveshaft Wrench, P/N 352877 336
Lower driveshaft Wrench, P/N 352877 316
Oetiker Pincers, P/N 787145 49
Pinion Bearing Remover and Installer,
P/N 391257 325, 329
Pinion Nut Holder, P/N 334455 318, 339
Pinion Nut Starting Tool, P/N 342216 339
Piston Stop Tool, P/N 342679 158
Plug/Holder, P/N 329661 220
Primary Lock Tool, P/N 777077 169
Propeller Shaft Adapter, P/N 432398 341
Puller Bridge, P/N 432127 326, 347, 350
Retaining Ring Pliers 238
Ring Compressor, P/N 336313 253
Ring Compressor, P/N 336314 253
Rod Cap Alignment Fixture, P/N 396749
256
Seal Installation Tool, P/N 326551 331,
351
Seal Installation Tool, P/N 330268 330
Seal Installation Tool, P/N 336311 331,
351
Secondary Lock Installer, P/N 777079 169
Secondary Lock Tool, P/N 777078 169
Shim Gauge Bar, P/N 328367 332
Shim Gauge Bar, P/N 349957 332
Shimming Screw, P/N 352878 332
Slide Hammer Adaptor Kit, P/N 390898
194
Slide Hammer, P/N 391008 194, 251, 319
Slide Hammer, P/N 432128 246, 286, 341
Small Puller Jaws, P/N 432131 326, 350
Spanner Wrench, P/N 432400 345, 349
Stator Test Adaptor, P/N 5006211 142
Temperature Gun, P/N 772018 228
8
Terminal Release Tool, P/N 351413 170
Test Propeller 18
Thermal Joint Compound, P/N 322170 229
Tilt Cylinder End Cap Remover/Installer,
P/N 326485 378, 385
Tilt Cylinder Seal Protector, P/N 326005
381
Tilt Tube Service Kit, P/N 434523 285
Timing Light 120
Torquing Socket, P/N 331638 243, 257
Transom Drill Fixture, P/N 434367 54
Trim Cylinder End Cap Remover/Installer,
P/N 436710 382, 385
Trim/Tilt Service Kit, P/N 390010 367
Trim/Tilt Service Kit, P/N 434524 367
Universal Puller Set, P/N 378103 315,
S–17
Universal Shift Rod Height Gauge,
P/N 389997 314
Universal Spanner Wrench, P/N 912084
378, 382, 385
Wrench Retainer, P/N 341438 318, 339
Wrist Pin Bearing Tool, P/N 336660 252
Wrist Pin Cone, P/N 318600 253
Wrist Pin Pressing Tool, P/N 326356 244
Wrist Pin Retaining Ring Driver,
P/N 318599 253
Torque Charts
see Service Charts
Standard 20
TPS Calibration 110
Trailering Bracket 358
Lubrication 84
Trim and Tilt
Assembly 380, 383, 389
Circuits 151
Disassembly 376, 382, 388
Electrical Circuit Tests 152
Fluid 387
Inspection 365
Lubrication 86
Modes of Operation 359
Motor Installation 386
Pressure Leakdown Test 367
Relays 151
Removal 373