Danfoss VLT AutomationDrive Design Manual page 82

FC 300 Selection
Mains Supply 3 x 525- 690V AC
FC 302
High/ Normal Load*
Typical Shaft output at 550V [kW]
Typical Shaft output at 575V [HP]
Typical Shaft output at 690V [kW]
Enclosure IP21, 54 without/ with
options cabinet
Output current
Continuous
(at 550V) [A]
Intermittent (60 sec overload)
(at 550V) [A]
Continuous
(at 575/690V) [A]
Intermittent (60 sec overload)
(at 575/690V) [A]
Continuous KVA
(at 550V) [KVA]
Continuous KVA
(at 575V) [KVA]
Continuous KVA
(at 690V) [KVA]
Max. input current
Continuous
(at 550V ) [A]
Continuous
(at 575V) [A]
Continuous
(at 690V) [A]
Max. cable size, motor [mm
(AWG
Max. cable size,mains F2 [mm
(AWG
Max. cable size,mains F4 [mm
(AWG
Max. cable size, loadsharing [mm
(AWG
Max. cable size, brake [mm
(AWG
Max. external mains fuses [A]
Estimated power loss
at 600V [W]
Estimated power loss
at 690V [W]
F3/F4 Max added losses CB or
Disconnect & Contactor
Max panel options losses
Weight,
enclosure IP21, IP54 [kg]
Weight, Rectifier Module [kg]
Weight, Inverter Module [kg]
Efficiency
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload = 160% torque during 60 sec., Normal overload = 110% torque during 60 sec.
1) For type of fuse see section Fuses.
2) American Wire Gauge.
3) Measured using 5 m screened motor cables at rated load and rated frequency.
4) The typical power loss is at nominal load conditions and expected to be within +/-15% (tolerence relates to
variety in voltage and cable conditions).
Values are based on a typical motor efficiency (eff2/eff3 border line). Motors with lower efficiency will also add to
the power loss in the frequency converter and opposite.
If the switching frequency is increased compared to the default setting, the power losses may rise significantly.
LCP and typical control card power consumptions are included. Further options and customer load may add up to
30W to the losses. (Though typical only 4W extra for a fully loaded control card, or options for slot A or slot B,
each).
FC 300 Design Guide
HO
750
1050
900
988
1482
945
1418
941
941
1129
962
920
920
2
2) )]
2
2)
)]
2
2)
)]
2
2) )]
2
2) )
1
11329
4)
11681
4)
556
4)
®
MG.33.BD.02 - VLT is a registered Danfoss trademark
P900 P1M0
NO HO
850 850
1150 1150
1000 1000
F2/ F4 F2/ F4
1108 1108
1219 1662
1060 1060
1166 1590
1056 1056
1056 1056
1267 1267
1079 1079
1032 1032
1032 1032
12x150
(12x300 mcm)
8x240
(8x500 mcm)
8x456
(8x900 mcm)
4x120
(4x250 mcm)
6x185
(6x350 mcm)
1600 2000
12909 12570
13305 12997
665 634
400
1246/ 1541 1246/ 1541
136 136
102 102
0.98
0-500Hz
105°C 105°C
75°C
P1M2
NO HO NO
1000 1000 1100
1350 1350 1550
1200 1200 1400
F2/ F4
1317 1317 1479
1449 1976 1627
1260 1260 1415
1386 1890 1557
1255 1255 1409
1255 1255 1409
1506 1506 1691
1282 1282 1440
1227 1227 1378
1227 1227 1378
2500
15358 15258 17602
15865 15763 18173
863 861 1044
1280/1575
136
136
95°C
81
4 4