Danfoss VLT FC 300 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Danfoss Manuals
  4. Relays
  5. VLT FC 300
  6. Operating instructions manual
Danfoss VLT FC 300 Operating Instructions Manual

Danfoss VLT FC 300 Operating Instructions Manual

Extended relay card
Hide thumbs Also See for VLT FC 300:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Operating Instructions Manual
FC 300 Extended Relay Card Operating In-
structions
Contents
Introduction to Extended Relay Card MCB 113
How to Install
MI.33.G2.02 - VLT® is a registered Danfoss trademark
Contents
3
3
3
4
5
7
7
7
7
8
9
9
9
11
11
19
22
23
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VLT FC 300 and is the answer not in the manual?

Questions and answers

Related Manuals for Danfoss VLT FC 300

Summary of Contents for Danfoss VLT FC 300

  • Page 1: Table Of Contents

    4. How to Install How to Install Installation of Option in the Frequency Converter 5. Parameter Set-up 5-** Digital In/Out 6-** Analog Outputs 14-** 24 V DC External Supply 16-** Data readouts MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 2 FC 300 Extended Relay Card Operating In- 1. How to Read these Operating Instructions structions MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 3: How To Read These Operating Instructions

    Chapter 5, Parameter Set-up, shows the parameter settings associated with the VLT Extended Relay Card MCB 113. 1.1.1. Approvals 1.1.2. Symbols Symbols used in these Operating Instructions. Indicates something to be noted by the reader. Indicates a general warning. Indicates a high-voltage warning. ∗ Indicates default setting MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 4: Abbreviations

    NAMUR NE37 German recommendations, commonly used within the Chemical Industry ”Realisation of Frequency Converters Standard Terminal Strip for Variable-speed Drives” Ampere/AMP Alternating current Direct current Electromagnetic Compatibility Hertz Parameter par. Volts Mili MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 5: Safety And Conformity

    When used in situations where safety is critical, e.g. when controlling the electromagnetic brake function of a hoist application, these control signals must not be relied on exclusively. Touching the electrical parts may be fatal - even after the equipment has been disconnected from mains. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 6 30 minutes For further information, please see the VLT Automation Drive FC 300 Operating Instructions, MG.33.AX.YY or the VLT Automation Drive FC 300 Design Guide, MG.33.BX.YY x = version number y = language MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 7: Introduction To Extended Relay Card Mcb 113

    3. Introduction to Extended Relay Card MCB 113 3.1. Introduction to Extended Relay Card MCB 113 The VLT Extended Relay Card MCB 113 is constructed as a standard C1 option for the Danfoss VLT AutomationDrive FC 300 and is automatically detected after mounting.

  • Page 8: Electrical Data

    High trigger level 17 V Analog Outputs: Number Range 0/4 -20 mA Resolution 11 bit Linearity < 0.2% IEC 61000-6-2 and IEC 61800-3 regarding Immunity of BURST, ESD, SURGE and Conducted Immunity MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 9: How To Install

    Enclosure A5 - C The mounting kits for these enclosures include a fan. Note that this fan is not to be mounted! For these enclosures only one C option can be installed at a time. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 10 4. How to Install structions Enclosure A2, A3 (and B3) 40 mm (only one C option). Enclosure A2, A3 (and B3) 60 mm (one C0 plus one C1 option, i.e. MCO 305 plus MCB 113). MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 11: Parameter Set-Up

    FC 300 standard terminals are 18, 19, 27, 29, 32 and 33. MCB 101 terminals are X30/2, X30/3 and X30/4. Terminal 29 functions as an output only in FC 302. Functions dedicated to only one digital input are stated in the associated parameter. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 12 Same as Preset ref bit 0 [16]. Preset ref. bit Preset ref. 0 Preset ref. 1 Preset ref. 2 Preset ref. 3 Preset ref. 4 Preset ref. 5 Preset ref. 6 Preset ref. 7 MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 13 Use pulse sequence as either reference or feedback. Scaling is done in par. group 5-5*. [34] Ramp bit 0 Enables a choice between one of the 4 ramps available, according to the table below. [35] Ramp bit 1 Same as Ramp bit 0. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 14 5-25 Terminal X46/11 Digital Input Option: Function: [0] * No operation This parameter is active when option module MCB 113 is installed in the frequency converter. Follow the function stated in 5-1* MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 15 Logic ‘0’. [28] Brake, no brake warning Brake is active and there are no warnings. [29] Brake ready, no fault Brake is ready for operation and there are no faults. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 16 . The input will go high whenever the Smart Logic Action [40] Set dig. out. A high is executed. The input will go low whenever the Smart Logic Action [34] dig. out. A low is executed. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 17 Out of speed range [16] Below speed, low [17] Above speed, high [18] Out of feedb. range [19] Below feedback, low [20] Above feedback, high [21] Thermal warning [22] Ready,no thermal W MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 18 Logic Controller digital output F [120] Local ref active [121] Remote ref active [122] No alarm [123] Start command activ [124] Running reverse [125] Drive in hand mode [126] Drive in auto mode MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 19: Analog Outputs

    Option: Function: Select the function of Terminal X45/1 as an analog current output. No operation When no signal on the analog output. [52] MCO 305 0-20 mA [53] MCO 305 4-20 mA MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 20 Par. 4-54 defines the behaviour of the analog output in case of bus time-out. [142] Bus ctrl. 4-20 mA, timeout Par. 4-54 defines the behaviour of the analog output in case of bus time-out. [150] Max Out Freq 4-20 mA In relation to par. 4-19. MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 21 Resolution on analog output is 11 bit. 6-80 Terminal X45/3 Output Option: Function: Select the function of Terminal X45/3 as an analog current output. [0] * No operation Same selections available as for par. 6-70 MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 22: 24 V Dc External Supply

    [1] * Select Yes [1] if an external 24 V DC supply will be used to power the option. I/O will be galvanically isolated from the drive when operated from an external supply. MI.33.G2.02 - VLT® is a registered Danfoss trademark...

  • Page 23: Data Readouts

    DI T-32 DI T-29 DI T-27 DI T-19 DI T-18 DI T-37 DI X30/4 DI X30/3 DI X30/2 DI X46/13 DI X46/11 DI X46/9 DI X46/7 DI X46/5 DI X46/3 DI X46/1 130BA894.10 MI.33.G2.02 - VLT® is a registered Danfoss trademark...
  • Page 24 View the actual value at output X45/1. The value shown reflects the selection in par. 6-70. 16-79 Analog Out X45/3 [mA] Range: Function: 0.000 N/A* [0.000 - 30.000 N/A] View the actual value at output X45/3. The value shown reflects the selection in par. 6-80. MI.33.G2.02 - VLT® is a registered Danfoss trademark...

Table of Contents