Danfoss VLT AutomationDrive Design Manual page 67

FC 300 Selection
Mains Supply 3 x 380 - 500 VAC
FC 302
High/ Normal Load*
4 4
Output current
Max. input current
* High overload = 160% torque during 60 sec., Normal overload = 110% torque during 60 sec.
66
FC 300 Design Guide
P90K
HO
Typical Shaft output at
90
400V [kW]
Typical Shaft output at
125
460V [HP]
Typical Shaft output at
110
500V [kW]
EnclosureIP21 D1
EnclosureIP54 D1
Enclosure IP00 D3
Continuous
177
(at 400V) [A]
Intermittent (60 sec
overload) 266
(at 400V) [A]
Continuous
160
(at 460/ 500V) [A]
Intermittent (60 sec
overload) 240
(at 460/ 500V) [A]
Continuous kVA
123
(at 400V) [kVA]
Continuous kVA
127
(at 460V) [kVA]
Continuous kVA
139
(at 500V) [kVA]
Continuous
171
(at 400V) [A]
Continuous
154
(at 460/ 500V) [A]
Max. cable size, mains
2 x 70
motor, brake and load
(2 x 2/0)
2 2)
share [mm (AWG )]
Max. external mains
300
fuses [A] 1
Estimated power loss
2369
at 400V [W] 4)
Estimated power loss
2162
at 460V [W]
Weight,
enclosure IP21, IP 54 96
[kg]
Weight,
82
enclosure IP00 [kg]
4)
Efficiency
Output frequency
Heatsink overtemp. trip 90 °C
Power card ambient trip
MG.33.BD.02 - VLT
P110
NO HO NO HO
110 110 132 132
150 150 200 200
132 132 160 160
D1
D1
D3
212 212 260 260
233 318 286 390
190 190 240 240
209 285 264 360
147 147 180 180
151 151 191 191
165 165 208 208
204 204 251 251
183 183 231 231
2 x 70
(2 x 2/0) (2 x 300 mcm)
350
2907 2634 3357 3117
2599 2350 3078 2886
104
91
0 - 800 Hz
110 °C
®
is a registered Danfoss trademark
P132 P160
NO HO NO
160 160 200
250 250 300
200 200 250
D2 D2
D2 D2
D4 D4
315 315 395
347 473 435
302 302 361
332 453 397
218 218 274
241 241 288
262 262 313
304 304 381
291 291 348
2 x 150 2 x 150
(2 x 300 mcm)
400 500
3914 3640 4812
3781 3629 4535
125 136
112 123
0.98
110 °C 110 °C
75 °C
P200
HO NO
200 250
300 350
250 315
D2
D2
D4
395 480
593 528
361 443
542 487
274 333
288 353
313 384
381 463
348 427
2 x 150
(2 x 300 mcm)
630
4288 5517
3624 5025
151
138
110 °C