Specifications; Bvp-900/900P - Sony BVP-900 Series System Manual

8-2 Specifications

8-2-1 BVP-900/900P

Pick-up device (when an OHB-750A/750AP is
installed)
2
Pick-up device / -inch, frame interline transfer
3
CCD
Device configuration
RGB 3-CCD system
BVP-900: 1038 (h) × 504 (v)
Picture elements
BVP-900P: 980 (h) × 582 (v)
Optical specifications (when an OHB-750A/
750AP is installed)
Spectral system F 1.4 prism system
Built-in filters Color temperature conversion
filters
A: Cross filter
B: 3200K (Clear)
C: 4300K
D: 6300K
E: 8000K
ND filters
1: Clear
2:
3:
4:
5:
General
Operating temperature
–20°C to +45°C (–4°F to +113°F)
Storage temperature –20°C to +50°C (–4°F to +122°F)
Mass Approx. 20 kg (44 lb 1 oz)
(main unit only)
Electrical characteristics (when an OHB-750A/
750AP is installed)
Sensitivity 2,000 lux (F 8.0)
Reflection ratio of 89.9%
Minimum subject illumination
About 7.5 lux (F 1.4, +18 dB
gain)
Video signal-to-noise ratio
BVP-900: 65 dB (typical)
BVP-900P: 63 dB (typical)
Resolution 900 TV lines (center of screen)
Registration 0.02% all zones (not including
lens distortion)
Geometric distortion Not recognized (not including
lens distortion)
..........................................................................................................................................................................................................
1) With an optional Stand-Alone Kit installed.
1
/ ND
4
1
/ ND
8
1
/ ND
16
1
/ ND
64
Input connectors
1)
REF IN BNC type (1)
1.0 Vp-p, 75-ohm terminated
1)
DC IN 4-pin (1)
RET CONTROL 6-pin (1)
AUDIO IN CH-1, CH-2
XLR 3-pin, female (1 each)
When the AUDIO IN switch is
set to MIC: –60 dBu (adjustable
to –20 dBu with the CCU-700A/
700AP), balanced
When the AUDIO IN switch is
set to LINE: –20 dBu, balanced
Output connectors
TEST OUT BNC-type (1)
1.0 Vp-p, 75-ohm terminated
1)
VIDEO OUT BNC-type (1)
1.0 Vp-p, 75-ohm terminated
VF D-sub 25-pin (1)
SCRIPT 4-pin (1)
5 W, 12 V DC
INTERCOM 1, INTERCOM 2
XLR 5-pin (1 each)
Input/output connectors
PROMPTER BNC-type (1)
1.0 Vp-p, 75-ohm terminated
CCU BVP-900: King type (1)
BVP-900P: Fischer type (1)
Lens connector 36-pin (1)
1)
VTR 26-pin (1)
TRACKER 10-pin (1)
REMOTE 8-pin multiconnector (1)
OHB 29-pin (1)
Supplied accessories
Angle adjustment fittings (2)
Front cover (1)
Number plates: For an up tally (1)
For a side panel (2)
For a back tally (1)
Belt for the cable clamp (2)
Operation Manual (1)
Maintenance Manual (1)
Design and specifications are subject to change
without notice.
8-11
Chapter 8 Specifications