Sony BVP-900 Series System Manual page 101

3-1 Internal Boards
8 ENG (engineer line) controls
Adjust the engineer line.
2W LEVEL: For adjusting the level when a 2W
intercom system is used.
2W CANCEL: For adjusting the leakage of the talk
signal to the receive line when a 2W intercom
system is used.
RTS CANCEL: For adjusting the leakage of the talk
signal to the receive line when an RTS intercom
system is used.
9 PROD (producer line) controls
Adjust the producer line.
2W LEVEL: For adjusting the level when a 2W
intercom system is used.
2W CANCEL: For adjusting the leakage of the talk
signal to the receive line when a 2W intercom
system is used.
RTS CANCEL: For adjusting the leakage of the talk
signal to the receive line when an RTS intercom
system is used.
0 S1001 switch
Sets the camera number of the system in which the
CNU-700 is not used.
For details, see "3-2-5 Setting the Camera Number and
Group Number."
!¡ S1002 switch
Used for setting and adjusting the camera system.
When S1002-7 switch is set to ON, the color-bar
character function is set to ON.
For details, see "3-3 Checking and Adjusting the Signal of
the System."
!™ S2491 switch
Selects the intercom system for an engineer line.
2W: When a 2W system is used
4W: When a 4W system is used
RTS: When an RTS system is used
Factory setting: 4W
!£ S2241 switch
Selects the intercom system for a producer line.
2W: When a 2W system is used
4W: When a 4W system is used
RTS: When an RTS system is used
Factory setting: 4W
!¢ S2822 switch
Selects the power source for the green tally system,
together with the S2821 switch.
POWER: For 24 V power supply
TTL: For 5 V power supply
Factory setting: POWER
3-20
Chapter 3 Initial Settings
!∞ S2821 switch
Selects the power source for the green tally system,
together with the S2822 switch.
POWER: For 24 V or 5 V power supply
CONTACT: For contact supply
Factory setting: POWER
!§S2791 switch
Selects the power source for the red tally system,
together with the S2792 switch.
POWER: For 24 V or 5 V power supply
CONTACT: For contact supply
Factory setting: POWER
!¶S2792 switch
Selects the power source for the red tally system,
together with the S2791 switch.
POWER: For 24 V power supply
TTL: For 5 V power supply
Factory setting: POWER
!•S2081 switch
Sets the program audio signal level, 0 dBu or
–20 dBu, according to the system audio level.
Factory setting: 0 dBu
!ªS2061 switch
Select the operating mode of the intercom system,
1CH (one channel) or 2CH (two channels).
Factory setting: 2CH
@ºS2341 switch
Selects the intercom line of the CCU-700A/700AP.
ON: For mixing the producer and engineer lines
OFF: For selecting the intercom line with the INCOM
SELECT switch on the front panel of the AT board.
Factory setting: OFF
@¡S2082 switch
Selects whether the program audio signal is to be
mixed with the intercom audio signal or not.
Factory setting: OFF (not mixed)
@™ S301 switch
Sets the level of the audio signal output from the MIC
OUTPUT CH-2 connector on the rear panel.
Factory setting: 0 dBu
@£ S201 switch
Sets the level of the audio signal output from the MIC
OUTPUT CH-1 connector on the rear panel.
Factory setting: 0 dBu