Eldes ESIM384 Installation Manual page 179

tErM
Keybus
Keyfob
LeD
Main Power
Master/User Code
MS mode
Normally closed (NC)
Normally open (NO)
On-board
Partition
Periodic test event
Peripheral device
PGM output
Ping period
Protocol
Relay
Scheduler
Service mode
SMS forward
tamper
transformer
ESIM384 Installation and Configuration Manual v1.1
DESCrIPtIon
A circuit (usually 4-wire) which provides power and serial data connection between keypads and
other accessories and the alarm panel.
A small security hardware device with built-in authentication used for system's security control
Stands for "Light emitting diode", defined as a solid-state light source that emits variable light, or
invisible, infrared radiation.
the main power source of the system.
Allows to carry out system arming/ disarming as well as minor system configuration and control by
the keypad.
is mode that enables data transmission from the eSIM384 alarm system to the
monitoring station.
is a switch that passes current until actuated.
is a switch that must be actuated to pass current.
is some element that is installed and functional within a device (system).
System comes equipped with a partitioning feature that can divide the alarm system into a number
of independently controlled areas identified as Partition 1 through 4, which are all supervised by
one alarm system unit. Partitioning can be used in installations where shared alarm system is more
practical, such as a house and a garage or within a single multi-storey building. When partitioned,
each system element, like zone, user phone number, keypad, user password, iButton key and eWK1/
eWK2 wireless keyfob can be assigned to single or multiple partitions. the user will then be able to
arm/disarm the system partition (-s) that the zones and arm/disarm method, except eKB2 keypad,
are assigned to.
Provides the following information on alarm system: date & time, status (armed/disarmed), GSM
signal strength, mains power supply status, temperature value measured by primary and secondary
temperature sensors (if any). the system sends this information to User 1 at the time intervals pro-
grammed into the scheduler.
A peripheral device is defined as a device, such as a keyboard, that is not part of the essential system
i.e., the memory and microprocessor.
these devices are intended to be connected to the system and used.
A PGM output is a programmable output that toggles to its set up state when a specific event has
occurred in the system, the scheduled weekday and time has come or if the user has initiated the
PGM output state change manually.
Sets period of time defining how often eSIM384 sends ping data packet to the Cloud Services server.
A formal specification for communicating; an IP address the special set of rules that end points in a
telecommunication connection use when they communicate. Protocols exist at several levels in a
telecommunication connection.
is an electromagnetic device opted for remote or automatic control that is actuated by variation in
conditions of an electric circuit and that operates in turn other devices (as switches) in the same or
a different circuit.
through the use of the system's built-in clock, it is possible to schedule automatic operations such
as setting and unsetting output state.
Mode that should be used when it is necessary to re-install some of the peripheral devices (to
change batteries, open/close enclosure and etc.). In this mode, system does not check for tamper
faults so it won't start siren alarm or send specified notifications to monitoring station or by SMS
text messages to users. Service Mode can be enabled only when system is disarmed.
System can re-sent all incoming SMS messages to the specified users. It is useful if the GSM operator
of the inserted SIM card sends some useful information (SIM card validation or payment account
status and etc.) or it is necessary to monitor all incoming SMS messages by specified user.
the tamper circuit is a single closed loop such that a break in the loop at any point will cause a tam-
per alarm regardless of the system status – armed or disarmed.
A device formed by two or more windings, that are magnetically coupled to each other and provide
a transfer of power electromagnetically from one winding to another.
179
EN 179