Lenze 9300 System Manual page 587

Show/Hide Bookmarks
Feed, 7-36
Position, 7-28
Traversing speed, 7-28
Free piece counter (FCNT), 7-198
Free space, 4-1
Freedigital outputs (FDO), 7-202
Freely assignable input variables (FEVAN), 7-204
Function block, POS, 7-24
Function block table, 7-20
Free codes (FCODE), 7-201
Free codes (FCODE), 7-201
Function blocks
Absolute value generator(ABS), 7-94
Addition block (ADD), 7-95
Analog input (AIN), 7-101
Analog output (AOUT), 7-107
Analog-digital converter (CONVAD), 7-155
Analog-phase converter (CONVAPH), 7-157
AND operation (AND), 7-103
Arithmetic blocks (ARIT), 7-109
Automation interface (AIF-IN), 7-96
Automation interface (AIF-OUT), 7-99
Changeover switch for analog signals (ASW), 7-113
Characteristic function (CURVE), 7-165
Comparator (CMP), 7-143
Configuration code, 7-6
connect, 7-7
Controller control (DCTRL)
Controllerinhibit (CINH), 7-170
Operation inhibited(DISABLE), 7-170
Quick stop (QSP), 7-170
TRIP RESET, 7-171
TRIP SET, 7-171
Controller control (DCTRLC), 7-169
CW-CCW-QSP link (R/L/Q), 7-254
Dead band(DB), 7-168
Delay element (PT1), 7-253
Delay elements (DIGDEL), 7-189
Derivative-action element (DT1), 7-197
Description of the, 7-20
Digital frequency input (DFIN), 7-172
Digital frequency output (DFOUT), 7-175
Digital frequency processing (DFSET), 7-185
Digital frequency ramp function generator (DFRFG), 7-179
Digital inputs (DIGIN), 7-192
Digital outputs (DIGOUT), 7-193
Digital status signals (STAT), 7-266
Display code, 7-6
Edge evaluation (TRANS), 7-278
Establish connections, 7-9
Fixed setpoint (FIXSET), 7-211
Flipflop (FLIP), 7-213
Free piece counter (FCNT), 7-198
Freedigital outputs (FDO), 7-202
Holding brake (BRK)
Applying the brake, 7-127
L
Table of keywords
Setting controller inhibit, 7-129
Holding brakes (BRK), Opening the brake, 7-128
Holding torque (BRK), 7-126
Input name, 7-5
Input symbol, 7-5
Internal motor control (MCTRL), 7-217
Inverter (ANEG), 7-106
Limiter (LIM), 7-216
Logic NOT, 7-231
Monitor outputs of monitoring system (MONIT), 7-227
Motor phase failure detection (MLP), 7-226
Motor potentiometer (MPOT), 7-228
Multi-axis synchronisation (SYNC), 7-268
Naming, 7-5
OR operation (OR), 7-239
Oscilloscope function (OSZ), 7-242
Output name, 7-6
Output symbol, 7-6
Parameter setting code, 7-6
Phase conversion (CONVPHPH2), 7-164
Phase integrator (PHINT), 7-250
Phase signal adaptation (PHDIV), 7-249
Process controller (PCTRL1), Dancer position, tension, pressure
controller, 7-246
Ramp generator(RFG), 7-255
Remove connections, 7-10
Sample and hold function (S&H), 7-257
Signal conversion (CONV), 7-152
Signal types, 7-4
Speed setpoint conditioning (NSET), 7-233
State bus connection, 7-267
System bus (CAN-IN), 7-131
System bus (CAN-OUT), 7-138
Table of the, 7-20
Function blocks , Freely assignable input variables (FEVAN),
7-204
Fuses, 3-6
Mains connection, 4-15
G
GDC
Offline operation, 5-6
Online operation, 5-6
Switch on, 5-6
Global Drive Control, 7-1
diagnostics, 8-1
parameter setting with, 7-319
Status indications, 6-2
Glossary, 16-1
EDSVS9332P EN 3.0
abc
17-3