Lenze 9300 System Manual page 463

Show/Hide Bookmarks
Configuration
Code
No. LCD
C0200 S/W ID
C0201 S/W DATE
C0202 INTERNAL IO
C0203 COMM. NO.
C0204 SERIAL-NO.
C0206 PRODUCT DATE
C0207 DL INFO 1
C0208 DL INFO 2
C0209 DL INFO 3
C0220 NSET TIR ADD
C0221 NSET TIF ADD
C0222 PCTRL VP
C0223 PCTRL TN
C0224 PCTRL KD
C0241 NSET RFG-I = O
C0244 BRK M SET
C0250 FCODE 1BIT
C0252 ANGLE OFFSET
C0253 ANGLE N-TRIM
C0254 VP ANGLE CTRL
C0255 THRESHOLD P03
C0260 MPOT1 HIGH
C0261 MPOT1 LOW
7-332
Possible settings
Lenze Selection
0.000
x / xxxx / xxxxx
0
0.000 0.000
0.000 0.000
1.0 0.1
400 20
0.0 0.0
1.00 0.00
0.00 -100.00
0 0 lower limit
1 upper limit
0 -245760000
→
-32767
0.4000 0.0000
327680 10
100.00 -199.99
-100.00 -199.99
EDSVS9332P-D22 EN 3.0
{0.001} 100.000 Internal identification
{1} 65535 Serial number
999.900 NSET
{0.001 s}
{0.001 s} 999.900 NSET
500.0 PCTRL
{0.1}
{1 ms} 99998 PCTRL
{0.1} 5.0 PCTRL
{0.01 %} 100.00 NSET
100.00 BRK1
{0.01 %}
245760000 DFSET
{1 inc}
{1 inc} 32767 DFSET
{0.0001} 3.9999 MCTRL
1800000000 Following error limit P03
{1 inc}
199.99 MPOT1
{0.01 %}
{0.01 %} 199.99 MPOT1
Important
Software identification
Software identification
Date of software release
Creation date
Commission number
Date of production
Download info 1
Download info 2
Download info 3
Additional setpoint Tir
Acceleration time T of the additional setpoint
ir
for NSET
(referring to speed variation of 0 ... n
max.
Additional setpoint Tif
Deceleration time T of the additional setpoint
if
for NSET
(referring to speed variation of 0 ... n
max.
Vp gain
Tn integral component
99999 ms: Switched off
Kd differential component
Threshold ramp function generator for main
setpoint
Input = output , (100 % = n )
max
Holding torque of the DC injection brake
100 % = value of C0057
FCODE 1bit digital
Phase offset
Fixed phase offset for digital frequency
configuration
1 rev. = 65536 inc
Speed-dependent phase trimming
depending on C0005, C0025, C0490
Change of C0005, C0025, or C0490 resets
C0253 to the default setting
1 rev. = 65536 inc
C0253 is reached at 15000 rpm
Vp phase controller
1 rev. = 65536 inc
Following error > C0255 releases fault "P03"
Upper limit (condition: C0260 > C0261)
Lower limit (condition: C0261 < C0260)
L
)
)