Inter-Tel CS-5200 Administrator's Manual page 59

INTER-TEL
6.
Trunk Programming
®
CS-5200/5400 ADMINISTRATOR GUIDE, ISSUE 1.1 – August 2005
Ring-In For Day Or Night Mode: To program the endpoint that will have ring in
for this trunk group for day mode, press
program for night mode, press
display shows ENTER ENDPOINT EXTENSION, enter endpoints into the list one
at a time as described above for Answer Access.
Toll Restriction: To program the toll restrictions for the trunk group, press
the
TOLL RESTRICTION
TION OPTION, press the numbers that correspond to the toll restrictions you want
to program, as follows:
1.) COS for day or night mode: To program the toll restriction class of service
for day mode, press
service for night mode, press
shows SET DAY (or NIGHT) COS XX. If this is not the COS you want to
program, scroll to the correct COS by pressing the high end of the Volume
button or the
NEXT
Volume button or the
COS numbers are listed below. For definitions, refer to "Class of Service" on
page 158. COS 01 is not used for trunks. When the correct COS is displayed,
press or the ON
1
the menu button to disable it. If desired, repeat this step to program addi-
OFF
tional COS toll restrictions. Then press
COS 02 – Deny Area/Office
COS 03 – Deny Operator
COS 04 – Deny Toll Access
COS 05 – Deny International
2.) Exempt from ARS: To program the Exempt from ARS option, press
the
EXEMPT FROM ARS
ARS, press or the
1
the NO menu button to disable it. Then press
3.) Subject to toll restriction: To program the trunk group Subject to Toll Restric-
tion option, press
play shows SUBJECT TO TOLL, press
the option. Or, press
or ACCEPT to continue.
Trunk List: To program the list of trunks for the trunk group, press
TRUNK LIST menu button. When the display shows ENTER TRUNK EXTEN-
SION, enter trunks into the list as follows:
1.) Enter a trunk extension using one of the methods described on
2.) The display shows the extension number and a Yes/No prompt. Press
the menu button, followed by
YES
press or the NO
2
the list.
3.) When the display returns to ENTER TRUNK EXTENSION, select another
extension number. Or, if finished programming the trunk list, press
ACCEPT to continue.
c. To exit, press
or
#
reach the ENTER DATABASE OPTION prompt.
When finished with all programming, press
OPTION prompt is displayed. This ends the programming session.
or the
3
or the
RING-IN NIGHT
4
menu button. When the display shows TOLL RESTRIC-
or the COS DAY menu button. To program class of
1
or the
COS NIGHT
2
menu button to scroll forward, or press the low end of the
PREVIOUS menu button to scroll backward. The default
menu button to enable the toll restriction. Or, press
or
#
COS 06 – Deny Equal Access
COS 07 – Deny Local Calls
COS 08 – Denied Numbers
COS 09 – Allowed Numbers
button. When the display shows EXEMPT FROM
menu button to enable the option. Or, press
YES
or the SUBJECT TO TOLL
4
1
or the NO menu button to disable it. Then press
2
, to include the trunk in the list. Or,
#
menu button, followed by
to move backward through the prompts until you
ACCEPT
#
Administrator Procedures
menu button. To
RING-IN DAY
menu button. When the
menu button. The display
ACCEPT to continue.
or ACCEPT to continue.
#
menu button. When the dis-
or the YES menu button to enable
6
page 39.
, to exclude the trunk from
#
while the ENTER DATABASE
Page 41
or
5
or
2
or
3
or
2
#
or the
or
1
or
#