Dell Force10 C150 Configuration Manual page 1076

Command Syntax
ntp server
ip-address
[ version
number
R6_E300(conf)#1w6d23h : NTP: xmit packet to 192.168.1.1:
leap 0, mode 3, version 3, stratum 2, ppoll 1024
rtdel 0219 (8.193970), rtdsp AF928 (10973.266602), refid C0A80101 (192.168.1.1)
ref CD7F4F63.6BE8F000 (14:51:15.421 UTC Thu Apr 2 2009)
org CD7F4F63.68000000 (14:51:15.406 UTC Thu Apr 2 2009)
rec CD7F4F63.6BE8F000 (14:51:15.421 UTC Thu Apr 2 2009)
xmt CD7F5368.D0535000 (15:8:24.813 UTC Thu Apr 2 2009)
1w6d23h : NTP: rcv packet from 192.168.1.1
leap 0, mode 4, version 3, stratum 1, ppoll 1024
rtdel 0000 (0.000000), rtdsp AF587 (10959.090820), refid 4C4F434C (76.79.67.76)
ref CD7E14FD.43F7CED9 (16:29:49.265 UTC Wed Apr 1 2009)
org CD7F5368.D0535000 (15:8:24.813 UTC Thu Apr 2 2009)
rec CD7F5368.D0000000 (15:8:24.812 UTC Thu Apr 2 2009)
xmt CD7F5368.D0000000 (15:8:24.812 UTC Thu Apr 2 2009)
inp CD7F5368.D1974000 (15:8:24.818 UTC Thu Apr 2 2009)
rtdel-root delay
rtdsp - round trip dispersion
refid - reference id
org -
rec - (last?) receive timestamp
xmt - transmit timestamp
mode - 3 client, 4 server
stratum - 1 primary reference clock, 2 secondary reference clock (via NTP)
version - NTP version 3
leap -
• Leap Indicator (sys.leap, peer.leap, pkt.leap): This is a two-bit code warning of an impending leap
second to be inserted in the NTP time scale. The bits are set before 23:59 on the day of insertion and
reset after 00:00 on the following day. This causes the number of seconds (rollover interval) in the day
of insertion to be increased or decreased by one. In the case of primary servers the bits are set by
operator intervention, while in the case of secondary servers the bits are set by the protocol. The two
bits, bit 0 and bit 1, respectively, are coded as follows:
• Poll Interval: integer indicating the minimum interval between transmitted messages, in seconds as a
power of two. For instance, a value of six indicates a minimum interval of 64 seconds.
• Precision: integer indicating the precision of the various clocks, in seconds to the nearest power of two.
The value must be rounded to the next larger power of two; for instance, a 50-Hz (20 ms) or 60-Hz
(16.67ms) power-frequency clock would be assigned the value -5 (31.25 ms), while a 1000-Hz (1 ms)
crystal-controlled clock would be assigned the value -9 (1.95 ms).
1076 | System Time and Date
[ key ] [ prefer ]
keyid
]
Command Mode Purpose
CONFIGURATION Configure an NTP server. Configure the IP
address of a server and the following optional
parameters:
•
•
•
key
keyid: Configure a text string as the key
exchanged between the NTP server and
client.
prefer: Enter the keyword to set this NTP
server as the preferred server.
version
Enter a number 1 to 3 as the
number:
NTP version.