Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
Enter the user name and password already set up on the device for the NSM
f.
administrator.
Enter a first connection one-time password. The device administrator will need
g.
it to connect with NSM from the member device.
Click Finish.
h.
Repeat Step 2 for the second cluster member, J-2.
3.
On cluster member J-1, configure and activate the connectivity with NSM.
4.
Log on to the J Series router.
a.
At the command-line prompt, identify the management system by device name,
b.
device ID, and HMAC:
For devices running the or 9.0 version of the operating system, use the following
command syntax:
set system services outbound-ssh application-id <name> secret <string>
services netconf device-id <external-id from nsm> <NSM device server ip>
port 7804
For example:
% set system services outbound-ssh application-id nsm-wei secret 123456789
services netconf device-id abcdef 10.150.42.16 port 7804
For devices running the 9.1 and later versions of the operating system, use the
following command syntax:
set system services outbound ssh client <name> secret <secret string>
services netconf device-id <external-id from nsm> <nsm device server ip>
port 7804
For example:
set system services outbound ssh client nsm wei secret 123456789
services netconf device-id abcdef 10.150.42.16 port 7804
Establish the SSH connection with the network management system.
c.
%
commit
The device software initiates the TCP connection to NSM and identifies itself
using the specified device ID and HMAC. The two sides then engage in SSH
transport layer interactions to set up an encrypted tunnel, and NSM authenticates
itself to the device based on user name and password.
In the Device List, verify the connection status of the cluster member. The status
d.
changes from "Never connected" to "Up."
If the configuration status is "platform mismatch," you selected the wrong
device platform when adding the device into NSM. Delete the device from
NSM and add it again using the correct device platform.
Chapter 4: Adding Devices
163
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
- Juniper 200 Series