Table of Contents
Advertisement
Copyright © 2010, Juniper Networks, Inc.
From the Platform list, select the device platform name.
From the Managed OS Version list, select the version of the operating system that
runs on the device.
Select the Device Server Connection Parameters. Use the default settings to
configure the device to connect to the NSM Device Server IP address and port.
Use a MIP to configure the device to connect to the NSM Device Server through a
mapped IP address and port.
Click Next.
Perform the following tasks on the Specify Device Admin User Name/Password and
6.
One Time Password screen:
a.
Make a note of the unique external ID. The device administrator will need it to
configure connectivity with NSM. The wizard automatically enters this value for
the device. This ID number represents the device within the management system.
b.
Specify the administrator user name and password for the SSH connection. This
name and password must match the name and password already configured
on the device.
c.
Specify the First Connection One Time Password (OTP) that authenticates the
device. Make a note of this password. The device administrator will need it to
configure the connectivity with NSM.
NOTE: All passwords handled by NSM are case-sensitive.
d.
Click Finish to complete the Add Device wizard and include the new device in
the Device Manager list.
Verify in the Device List tab that the new device is visible and has the connection
7.
status "Never connected."
Convey the unique external ID and the one-time password to the device manager.
8.
Configure and Activate the NSM Agent on the Secure Access or Infranet Controller
Device
Configure and activate the NSM agent on the Secure Access or Infranet Controller device
to establish SSH communications with NSM. On successful execution of these steps,
you can control the device from NSM,
Open the System > Configuration > NSM Agent screen to add the NSM management
1.
application.
In the Primary Server field, enter the IP address of the Device Server.
2.
In the Primary Port field, enter 7804.
3.
Fill out the Backup Server and Backup Port fields if a high availability Device Server
4.
is configured.
In the Device ID field, enter the unique external ID provided by the NSM administrator.
5.
Chapter 4: Adding Devices
123
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
- Juniper 200 Series