Table of Contents
Advertisement
Network and Security Manager Administration Guide
134
Updating the device also pushes the Juniper Networks Recommended policy to the
device.
After update is complete, the device status displays as "Managed", indicating that the
device has connected and the management system has successfully pushed the device
configuration.
Junos Devices
To activate a Junos device (or EX Series virtual chassis) with a static IP address:
Check the device configuration state by holding your mouse cursor over the device
1.
in Device Manager, or by checking the configuration status in Device Monitor. The
device configuration state should display "Modeled", indicating that the management
system is waiting for the device to connect.
Right-click the device and select Activate Device. The Activate Device wizard begins.
2.
Select Device deployed and IP is reachable.
3.
Click Next and enter the connection information:
4.
Enter the IP Address of the security device.
For a Junos device with redundant Routing Engines, provide the IP address of the
master Routing Engine.
Enter the device administrator name and password.
NOTE: All passwords handled by NSM are case-sensitive.
Click Next. The Verify Device Authenticity dialog box opens. The device wizard displays
5.
the RSA Key FingerPrint information. To prevent man-in-the-middle attacks, you
should verify the fingerprint using an out-of-band method.
Click Next to accept the fingerprint. The Detecting Device dialog box opens.
6.
After the wizard displays the autodetected device information, verify that the device
7.
type, OS version, and the device serial number are correct.
Click Next to activate the device in NSM.
8.
Click Update Now to update the configuration on the device with the settings from
9.
the modelled device, or click Exit to leave the wizard without updating the device.
If you do not update the configuration now, you will have to do it manually later by
right-clicking the device and selecting Update Device.
The Job Information box displays the job type and status for the update. When the
job status displays successful completion, click Close.
After the update is complete, the device status displays as "Managed", indicating that
the device has connected and the management system has successfully pushed the
device configuration.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
- Juniper 200 Series