Setting Paper On The Multi-Bypass Tray - Kyocera KM-C2630D Operation Manual

Section 3 PREPARATIONS

Setting paper on the multi-bypass tray

Up to 150 sheets of standard paper (Inch specifications: 60 g/m² -
105 g/m² [Metric specifications: 60 g/m
the multi-bypass tray.
• Acceptable sizes of paper
Inch specifications
5 " × 8 ", 8 " × 11", 11" × 8
1/2 1/2 1/2
× 17", 12" × 18", A6R, B6R, A5R, B5R, B5, A4R, A4, B4 and A3
Metric specifications
A6R, B6R, A5R, B5R, B5, A4R, A4, B4, A3, A3 wide (305 mm ×
457 mm), Folio, 5 " × 8
1/2 1/2
8 " × 14", 11" × 17" and 12" × 18"
1/2
When copying onto special paper, be sure to use the multi-bypass
tray.
NOTES
• The following types of special paper and the number of
sheets that can be set on the multi-bypass tray at one
time are as follows:
OHP transparencies: 25 sheets (ALWAYS fan through
transparencies before setting them on the multi-bypass
tray.)
Thick paper (91 g/m² – 220 g/m²): 25 – 100 sheets
(Depending on the paper size and weight)
• When using thick A4-size paper (200 g/m² or thicker),
load the paper with a long side as the leading edge.
Loading such paper with a short side as the leading
edge can cause paper jamming.
• The acceptable paper weight for thick paper actually
differs depending upon the size of the paper:
Under 11" × 8 " [A4]: 91 g/m² – 220 g/m²
1/2
Over 11" × 8 " [A4]: Inch specifications: 106 g/m² –
1/2
135 g/m² [Metric specifications: 91 g/m
• When the optional Document Finisher is installed on
your copier, paper of the following weights can be used:
When ejecting onto the sub tray: 60 g/m² – 105 g/m²
When ejecting onto the main tray: 60 g/m² – 220 g/m²
When stapling: 60 g/m
When hole punching: 60 g/m² – 105 g/m²
IMPORTANT!
• BE SURE to use paper that is specified for color copy
use in order to make clear color copies.
• DO NOT use paper such as that designated for inkjet
printers or any paper treated with special coating.
• When you press the "Bypass" key in the "Basic" tab on
the touch panel, the "Bypass setting" screen will be
displayed. In this case, you should refer to
"Multi-bypass tray paper settings" on page 7-99
and follow the procedure, starting from step 3, to
specify the size and type of paper to be used.
3-4
2 2
– 90 g/m ]) can be set on
", 8 " × 13", 8 " × 14", 11"
1/2 1/2 1/2
", 8 " × 11", 11" × 8 ", 8
1/2 1/2 1/2
2
– 135 g/m
2 2
– 105 g/m
1
Open the multi-bypass tray.
" × 13",
NOTE
When loading 8
sure to pull out the multi-bypass extension to match the
size of the paper.
2
]
2
Adjust the insert guides to fit the width of the paper that is
to be set on the multi-bypass tray.
" × 11" (A4R) size or larger paper, be
1/2