Komatsu D61EXi-24 Operation & Maintenance Manual page 207

INDEX
Project files - Export..............................................4-15
Project files - Import / Set......................................4-13
Push and turn operation........................................3-60
Radio - Configure..................................................3-21
Radio antenna - Remove...................................... 3-68
Radio device settings............................................4-48
Raising ground level operation (pushing up soils) 3-59
Range - Change....................................................4-97
Read this manual.................................................... 1-2
Received message - Check.................................. 4-66
Received message - Delete..................................4-68
Recommended applications and modes...............3-53
Right window display............................................ 4-77
Right window display - Display............................. 4-77
Safety information................................................... 1-6
Scraping depth - Set from current ground surface3-46
Select active file.................................................... 3-29
Set base point for checking blade elevation......... 3-25
Set base station.................................................... 3-21
Setting contents by Sitelink3D menu.................... 4-58
Shortcut on main window......................................4-89
Shortcuts display - Set.......................................... 4-83
Single point blade control - Set............................. 4-44
Sitelink3D - Connect............................................. 4-60
Sitelink3D - Register............................................. 4-58
Sitelink3D - Set..................................................... 4-57
Sitelink3D activity..................................................4-92
Sitelink3D messaging........................................... 4-92
Slope control key.................................................. 4-88
Slope display - Change.........................................4-97
Sloping surface files - Create................................4-28
Smooth start................................................. 3-43,3-47
Smooth start - Select............................................ 3-49
Specifications..........................................................5-2
Specifications - D61EXI-24..................................... 5-2
Specifications - D61PXI-24..................................... 5-2
Spreading operation..............................................3-57
Start engine.............................................................2-4
Start or stop As-built updates................................4-90
Steer indication options.........................................4-46
Steer indication options - Set................................ 4-46
Steer point - Move (pop-up menu)...................... 4-104
Steering operation to polyline............................. 4-102
Subgrade of an existing alignment - Create..........4-34
Super elevation operation..................................... 3-67
Supervisor mode...................................................4-70
Supervisor mode - Use......................................... 4-70
Surface file............................................................ 4-23
Surface files - Create after reflecting raise or lower
amount of an existing surface........................4-33
Surface files - Import.............................................4-23
Switches - Function.................................................4-5
R
S
Take a topo shot....................................................4-91
Task detail............................................................. 4-92
Task menu.............................................................4-68
Tilt cylinder - Reset stroke end..............................3-18
Toggle As-built mode............................................ 4-89
Toggle main view switch......................................... 4-6
Tools menu............................................................4-48
Topo shot for topographic survey..........................4-51
Transportation....................................................... 3-68
Triangulated surfaces - Create from a topo survey file
.......................................................................4-32
Troubles and actions.....................................3-44,3-71
View menu............................................................ 4-75
When finishing concave inflection point vertically. 3-65
When finishing convex inflection point.................. 3-66
When finishing slope surface by operating horizontal-
ly.................................................................... 3-65
When message is displayed on control box - Action....
.......................................................................3-72
When pop-up message is displayed on control box -
Action.............................................................3-75
When selecting no prompt.................................... 4-56
When selecting prompt for details.........................4-54
When spreading soils to places higher than blade
edge...............................................................3-58
When spreading soils to places lower than blade
edge...............................................................3-57
When you change blade control point on blade con-
trol screen...................................................... 4-45
When you change blade control point quickly.......4-45
Working surface display - Set............................... 4-79
Zoom in switch........................................................ 4-5
Zoom out switch......................................................4-5
T
V
W
Z
6-3