Komatsu D61EXi-24 Operation & Maintenance Manual page 205

INDEX
INDEX
Symbols
3DMC....................................................................4-86
3DMC - Exit ..........................................................4-37
3DMC information - Display.................................. 4-86
Actions when automatic blade control is activated.......
.......................................................................3-31
Actions when carry mode is activated...................3-38
Active alignment file - Select.................................4-36
Active file...............................................................4-36
Active surface file - Select.....................................4-36
Adjust blade elevation...........................................4-47
Adjust blade wear amount.................................... 4-47
Alignment display - Set......................................... 4-80
Angle cylinder - Reset stroke end......................... 3-19
Applicable operations by blade control lever with cut-
ting and carry mode....................................... 3-40
Applicable operations by tilting blade control lever
with cutting and carry mode...........................3-41
As-Built control options - Set.................................4-40
As-built surface display - Add............................... 4-41
As-built surface display - Delete........................... 4-42
As-built surface display - Set................................ 4-81
Ative as-built view - Select.................................... 4-37
Auto/Manual switch.................................................3-7
Automatic best-fit blade control - Set.................... 4-44
Back grade mode - Handle................................... 3-32
Back grade mode switch....................................... 3-11
Back grade work................................................... 3-64
Background color display - Set............................. 4-84
Battery disconnect switch - Turn off before long-term
storage...........................................................3-69
Blade - Activate automatic control........................ 3-29
Blade - Adjust elevation........................................ 3-28
Blade - Change lower edge position in cutting in..3-48
Blade - Check / Adjust elevation........................... 3-26
Blade - Check elevation........................................ 3-26
Blade - Control automatically................................ 3-21
Blade - Handle automatic control..........................3-29
Blade - Operate to travel reverse in automatic control.
.......................................................................3-32
Blade - Set dozing mode.......................................3-37
Blade - Set load mode.......................................... 3-45
Blade - Stop automatic control..............................3-35
Blade automatic control - Preparations.................3-21
Blade calibration................................................... 4-47
Blade control......................................................... 4-44
Blade edge - Take a topo shot of blade elevation for
topographic survey in certain interval............ 4-51
A
B
Blade edge - Take a topo shot of blade elevation for
topographic survey in preferable timing.........4-54
Blade edge and track shoe - Input wear amount.. 3-24
Blade elevation - Check........................................ 4-48
Blade load mode - Set.......................................... 3-42
Blade load selection..............................................4-91
Brightness and volume control................................4-7
Carry and compact soils....................................... 3-56
Carry mode........................................................... 3-38
Carry mode - Effective use................................... 3-43
Carry mode - Phenomena and actions................. 3-44
Carry soils to hole................................................. 3-55
Checks and adjustment before starting engine.....3-16
Checks before starting.......................................... 3-25
Construction information - Set.............................. 4-62
Control box..............................................................3-5
Control box - Phenomena and actions..................3-71
Control box - Set for connecting to machine.........4-38
Control box name....................................................3-4
Control menu........................................................ 4-38
Control point files.................................................. 4-17
Control point files - Import.....................................4-17
Controls and gauges names................................... 3-3
Crown road surface files - Create......................... 4-30
Cut/fill offsets - Adjust........................................... 4-96
Cut/fill offsets - Adjust (pop-up menu)...................4-99
Cut/fill offsets switch............................................. 3-10
Cutting and carry operation...................................3-55
Cylinder - Reset stroke end.......................... 3-17,3-25
Data - Output........................................................ 4-62
Display extended status text in plan/profile/section.....
.......................................................................4-98
Display options......................................................4-78
Display options - Display.......................................4-78
Displayed units - Set............................................. 4-84
Dozing control....................................................... 4-47
Dozing mode selection..........................................4-91
Elevation control key.............................................4-87
Engine - Stop........................................................ 3-19
Exit 3DMC.............................................................4-37
Explanation of components.....................................3-5
File menu.............................................................. 4-13
Finishing operation of bank soil............................ 3-64
Flat surface files - Create......................................4-25
C
D
E
F
6-1