Danfoss VLT AutomationDrive FC 301 Programming Manual page 191

Parameter Lists
4.1.22 30-** Special Features
Par. No. # Parameter description
30-0* Wobbler
30-00 Wobble Mode
30-01 Wobble Delta Frequency [Hz]
30-02 Wobble Delta Frequency [%]
Wobble Delta Freq. Scaling
30-03 Resource
30-04 Wobble Jump Frequency [Hz]
30-05 Wobble Jump Frequency [%]
30-06 Wobble Jump Time
30-07 Wobble Sequence Time
30-08 Wobble Up/ Down Time
30-09 Wobble Random Function
30-10 Wobble Ratio
30-11 Wobble Random Ratio Max.
30-12 Wobble Random Ratio Min.
30-19 Wobble Delta Freq. Scaled
30-2* Adv. Start Adjust
30-20 High Starting Torque Time [s]
High Starting Torque Current
30-21 [%]
30-22 Locked Rotor Protection
Locked Rotor Detection Time
30-23 [s]
30-8* Compatibility (I)
30-80 d-axis Inductance (Ld)
30-81 Brake Resistor (ohm)
30-83 Speed PID Proportional Gain
Process PID Proportional
30-84 Gain
4.1.23 32-** MCO Basic Settings
Par. No. # Parameter description
32-0* Encoder 2
32-00 Incremental Signal Type
32-01 Incremental Resolution
32-02 Absolute Protocol
32-03 Absolute Resolution
Absolute Encoder Baudrate
32-04 X55
Absolute Encoder Data
32-05 Length
Absolute Encoder Clock
32-06 Frequency
Absolute Encoder Clock
32-07 Generation
®
VLT AutomationDrive FC 301/302 Programming Guide
Default value 4-set-up
[0] Abs. Freq., Abs.
Time All set-ups
5 Hz All set-ups
25 % All set-ups
[0] No function All set-ups
0 Hz All set-ups
0 % All set-ups
ExpressionLimit All set-ups
10 s All set-ups
5 s All set-ups
[0] Off All set-ups
1 N/A All set-ups
10 N/A All set-ups
0.1 N/A All set-ups
0 Hz All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit All set-ups
ExpressionLimit 1 set-up
ExpressionLimit All set-ups
0.100 N/A All set-ups
Default value 4-set-up
[1] RS422 (5V TTL) 2 set-ups
1024 N/A 2 set-ups
[0] None 2 set-ups
8192 N/A 2 set-ups
[4] 9600 All set-ups
25 N/A 2 set-ups
262 kHz 2 set-ups
[1] On 2 set-ups
MG33MH02 - Rev. 2013-09-30
FC 302 Change Conver-
only during sion index
operation
FALSE -
TRUE -1
TRUE 0
TRUE -
TRUE -1
TRUE 0
TRUE -3
TRUE -1
TRUE -1
TRUE -
TRUE -1
TRUE -1
TRUE -1
FALSE -1
x TRUE -2
x TRUE -1
x TRUE -
x TRUE -2
x FALSE -6
TRUE -2
TRUE -4
TRUE -3
FC 302 Change Conver-
only during sion index
operation
TRUE -
TRUE 0
TRUE -
TRUE 0
FALSE -
TRUE 0
TRUE 0
TRUE -
Type
Uint8
4 4
Uint8
Uint8
Uint8
Uint8
Uint8
Uint16
Uint16
Uint16
Uint8
Uint8
Uint8
Uint8
Uint16
Uint16
Uint32
Uint8
Uint8
Int32
Uint32
Uint32
Uint16
Type
Uint8
Uint32
Uint8
Uint32
Uint8
Uint8
Uint32
Uint8
189