Xerox WorkCentre 5021 Service Documentation page 283

6.1.15 Print Speed
Continuous speed (PPM) of the print engine is defined as follows:
During output to Face Down Tray, taking the time from when the tail edge of the 1st sheet is
output from the IOT exit area until the tail edge of the 11th sheet is output from the MC exit
area to be t seconds, the no. of sheets that is printed in 1 minute is given by the formula: [(60/
t)x10 for 1 Sided and (60/t)x20 for 2 Sided] as shown in the following table. The numerical
value for Duplex is IPM (Images Per Minute).
Limitations
• This does not include the time for settings/cleaning/sagging/procon.
• When automatic recognition of paper size at the MSI is in operation, it prints at the corre-
sponding productivity rate of that paper size. However, if the paper size is not automati-
cally detected, the 1st paper is printed with the same productivity as the A3 SEF or 17'
paper. Immediately after that, the 2nd BTR is cleaned, then the 2nd and subsequent
paper will be printed with the productivity of the paper size that was detected when print-
ing the 1st paper.
20/18 IOT (feed from Tray/output to Center Tray)
Unit: 1 Sided: ppm, 2 Sided: ipm
216.0 mm or
shorter in the
SS direction
and 210.0
mm or longer
in the FS
direction
A4 LEF A5 SEF
8.5x11 LEF B5 SEF
B5 LEF 5.5x8.5 SEF
Paper
Type 1 2 1 2
Settings Sided Sided Sided Sided
Bond- 20/18 13.1/ 12/12 7.2/
PlainRe- 13.1 7.2
cycledPla
in Reload
*
*: There is no 2 Sided for Plain Reload
General Procedures
6.1.15, 6.1.16
Table 1
216.1 mm to 297.3 mm to 364.2 mm to
297.2 mm in 364.1 mm in 432.0 mm in the
the SS the SS SS direction
direction direction (A3S/11x17S)
B4 SEF
8.5x13
SEF8.5x14
A4 SEF SEF8.5x13.4 A3 SEF
8.5x11 SEF SEF 11x17 SEF
1 2 1 2
Sided Sided Sided Sided 1 Sided 2 Sided
15/14 8.7/ 12/12 7.9/7.9 10/10
8.7
6.1.16 Tray (Paper Feed)
6.1.16.1 Paper Trays
Paper Trays refer to all type of Trays that are pulled out towards the front. The Main Unit has
the MSI and the 250-sheet Paper Tray (1 level) as standard configuration.The 500-sheet Paper
Tray (Single Tray Module: STM) is available as a field option.The MSI is installed on the left
side of the IOT by standard.
6.1.16.2 Paper Tray Characteristics
IOT/ Tray Supported Paper
TM NO. (Standard Size)
IOT Tray1 Min:B5
Max:A3S,11X17S
MSI Min:A5S, 5.5X8.5
Max:A3S,11X17S
STM Tray2 Min:B5S
Max:A3S,11X17S
*1: B Zone/Fresh Paper, P Paper
6.1.16.3 Remaining Paper Amount Detection
Tray
Tray1-2
MSI
7.2/7.2
• When the power is turned OFF during liftup, if the power is turned ON again without
removing the Tray, and the Tray is inserted again while the Bottom Plate has not dropped,
the remaining paper amount cannot be detected correctly.
08/2012
6-14
Table 1
Supported
Paper Supporte
(Non-Standard d Paper Storage
Size) (W x L) Weight Capacity
mm (gsm) *1
Non-Standard 60-90 250sheets
Sizes not sup- (Business
ported 80gsm)
Non-Standard 60-110 100sheets
Sizes not sup- (Business
ported 70gsm)
Non-Standard 60-90 500sheets
Sizes not sup- (Business
ported 70gsm)
450sheets
(Business
80gsm)
Table 2
Detection & Notification Remarks
1 level: 0%
1 level: 0%
WorkCentre 5021/5019
Remarks
Stack height: 27
mm
Stack height: 10
mm
Stack height: 54
mm
Initial Issue