Xerox WorkCentre 5021 Service Documentation page 333

Chain-Link NVM Name
752-097 PRC_IMAGE_PIXEL_HI
752-098 PRC_IMAGE_PIXEL_LO
752-101 PRC_ACCUM_USE_ICDC_ACCUM
752-107 PRC_ICDC_MOVE_AVE_ACCUM_FEW
752-108 PRC_ICDC_MOVE_AVE_ACCUM_MANY
752-111 PRC_ICDC_MOVE_AVE_FEW
752-112 PRC_ICDC_MOVE_AVE_MANY
752-140 PRC_DISP_TONER_REMAIN_CORR_COEF
752-159 PRC_DELTA_ATC_TARGET_TEMP_CORR
752-160 PRC_DELTA_ATC_TARGET_HUMI_CORR
752-173 PRC_DELTA_AGE_ATC
752-176 PRC_DELTA_ATC_TARGET_DEVE_CORR
752-186 PRC_DELTA_ATC_TARGET_AC_CORR
752-188 PRC_ATC_MOD_TARGET
752-192 PRC_DELTA_ATC_TARGET_MANUAL_CORR
752-224 PRC_BCR_DC_OUT
752-225 PRC_BIAS_DC_OUT
752-226 PRC_LD_OUT
752-230 PRC_DELTA_LD_MANUAL_CORR
752-248 PRC_DELTA_VH_TEMP
752-278 PRC_DELTA_VH_PR
752-301 PRC_DELTA_LD_TEMP
752-317 PRC_DELTA_LD_HUMI
752-331 PRC_DELTA_LD_PR
752-344 PRC_DELTA_LD_EMP
752-350 PRC_DELTA_LD_MANUAL_CORR_MAX
752-351 PRC_DELTA_LD_MANUAL_CORR_MIN
752-352 PRC_DELTA_LD
752-398 PRC_FLAG_EMPTY_CHECK_STATE_ATC
752-402 PRC_ATC_EMPTY_CHECK_STATE1_CNT
752-403 PRC_BUFFER_EMPTY_CHECK_CNT
General Procedures
6.3.14
Table 1 NVM PROCON
Setting Setting
Range Range
(Minimum (Maximum Default
Value) Value) Value
0 16383 0
0 65535 0
0 2147483648 0
0 32767 0
0 32767 0
0 1023 0
0 1023 0
0 255 0
-999 999 0
-999 999 0
0 255 0
-999 999 0
-32768 32767 0
0 999 548
-512 511 0
0 1000 735
0 255 220
0 255 185
-100 100 0
-128 127 0
-128 127 0
-128 127 0
-128 127 0
-128 127 0
-128 127 0
0 100 0
-100 100 0
-128 127 0
0 3 0
0 65535 0
-30000 30000 0
08/2012
6-64
Write Initialization
Yes/No Yes/No Description
Enable Enable Image_Pixel_Hi
Enable Enable Image_Pixel_Lo
Enable Enable ICDC Accumulated Value for Measuring Accumu-
lated Usage
Enable Enable ICDC Moving Average Accumulated Value [Minority]
Enable Enable ICDC Moving Average Accumulated Value [Majority]
Enable Enable ICDC Moving Average Value [Minority]
Enable Enable ICDC Moving Average Value [Majority]
Enable Enable Disp Remaining Toner Correction Coefficient
Enable Enable Delta ATC Target Temperature Correction Amount
Enable Enable Delta ATC Target Humidity Correction Amount
Enable Enable Delta Age_ATC
Enable Enable Delta ATC Target Deve Correction Amount
Enable Enable Delta ATC Target AC Correction Amount
Enable Enable ATC Correction Target Value
Enable Enable Delta ATC Target Manual Correction Amount
Enable Enable BCR_DC_OUT
(0 ~ 1000 : -0 ~ -1000V)
Enable Enable BIAS_DC_OUT
(0 ~ 255 : 0 ~ -700V)
Enable Enable LD_OUT
(0 ~ 255 : 0 ~ 2V)
Enable Enable Delta LD_Manual Correction Amount
(0 ~ 255 : 0 ~ 2V)
Enable Enable Delta VHtemp
Enable Enable Delta VHpr
Enable Enable Delta LDtemp
Enable Enable Delta LDhum
Enable Enable Delta LDpr
Enable Enable Delta LDemp
disable Enable Delta LD_Manual Correction Amount Upper Limit
disable Enable Delta LD_Manual Correction Amount Lower Limit
Enable Enable Delta LD
Enable Enable Flag ATC empty detection state
0: Normal
1: Empty detection count in progress
2: NearEmpty
3: Empty
Enable Enable ATC empty detection state 1 count
Enable Enable Buffer empty detection count
Initial Issue
WorkCentre 5021/5019