Danfoss VLT AutomationDrive FC 300 Design Manual page 70

Selection
FC 302
High/Normal load
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [HP]
Typical shaft output at 690 V [kW]
Enclosure IP21, IP54 without/with
options cabinet
Output current
4 4
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)
[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at
575/690 V) [A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
Max. cable size, motor [mm
Max. cable size, mains [mm
Max. cable size, brake [mm
Max. external mains fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
F3/F4 Max added losses CB or
disconnect & contactor
Max panel options losses
Weight, enclosure IP21, IP54 [kg]
Weight, rectifier module [kg]
Weight, inverter module [kg]
4)
Efficiency
Output frequency
Power heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s
Table 4.13 Technical Specifications, F10/F11 frames, 525-690 V Mains Supply 6x525-690 V AC, 12-Pulse
1) American Wire Gauge.
2) For fuse ratings, see 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the frequency converter. If the
switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are included.
Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each add
only 4 W.
4) Measured using 5 m screened motor cables at rated load and rated frequency.
68
®
VLT AutomationDrive FC 300 Design Guide 90-1200 kW
P630
HO
500
650
630
F10/F11
659
989
630
945
628
627
753
642
613
613
2 1)
(AWG) ]
2 1)
(AWG) ]
2 (AWG) 1) ]
2)
3) 4) 8075
3) 4)
8388
342
102
102
95 °C
MG34S202 - Rev. 2013-08-19
P710
NO HO
560 560
750 750
710 710
F10/F11
763 763
839 1145
730 730
803 1095
727 727
727 727
872 872
743 743
711 711
711 711
8x150 (8x300 mcm)
6x120 (6x250 mcm)
4x185 (4x350 mcm)
900
9500 9165
9863 9537
427 419
400
1017/1319
102
102
0.98
0-500 Hz
105 °C
85 °C
± 15% (tolerance relates to variety in voltage and cable conditions.) These
P800
NO HO
670 670
950 950
800 800
F10/F11
889 889
978 1334
850 850
935 1275
847 847
847 847
1016 1016
866 866
828 828
828 828
10872 10860 12316
11304 11291 12798
532 519
102
136
95 °C
NO
750
1050
900
988
1087
945
1040
941
941
1129
962
920
920
615