Danfoss VLT AutomationDrive FC 300 Design Manual page 64

Selection
FC 302 High/Normal load*
Typical Shaft output at 550 V [kW]
Typical Shaft output at 575 V [hp]
Typical Shaft output at 690 V [kW]
Enclosure IP21
Enclosure IP54
Enclosure IP20
4 4
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V)
[kVA]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V)
Max. cable size: mains, motor, brake and load
share mm 2 (AWG)
Max. external mains fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
Weight, enclosure IP21, IP54 kg (lbs.)
Weight, enclosure IP20 kg (lbs.)
4)
Efficiency
Output frequency
Heatsink overtemperature trip
Control card ambient trip
*High overload=150% current for 60 s, Normal overload=110% current for 60 s.
Table 4.7 Technical Specifications, D-frame, 525-690 V Mains Supply 3x525-690 V AC
1) American Wire Gauge.
2) For fuse ratings, see 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the frequency converter. If the
switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are included.
Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each add
only 4 W.
4) Measured using 5 m screened motor cables at rated load and rated frequency.
62
VLT
1)
2)
3) 4)
3) 4)
®
AutomationDrive FC 300 Design Guide 90-1200 kW
N160 N200
HO NO HO
132 160 160
200 250 250
160 200 200
D2h D2h
D2h D2h
D4h D4h
201 253 253
302 278 380
192 242 242
288 266 363
191 241 241
191 241 241
229 289 289
198 245 245
189 234 234
197 240 240
2361 3074 3012
2446 3175 3123
± 15% (tolerance relates to variety in voltage and cable conditions.) These
MG34S202 - Rev. 2013-08-19
N250
NO HO NO
200 200 250
300 300 350
250 250 315
D2h
D2h
D4h
303 303 360
333 455 396
290 290 344
319 435 378
289 289 343
289 289 343
347 347 411
299 299 355
286 286 339
296 296 352
2x185 (2x350)
550
3723 3642 4465
3851 3771 4614
125 (275)
125 (275)
0.98
0–590 Hz
110 °C
80 °C
N315
HO NO
250 315
350 400
315 400
D2h
D2h
D4h
360 418
540 460
344 400
516 440
343 398
343 398
411 478
355 408
339 390
352 400
4146 5028
4258 5155