Danfoss VLT AutomationDrive FC 300 Design Manual page 66

Selection
FC 302
High/Normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [HP]
Typical shaft output at 690 V [kW]
Enclosure IP21
Enclosure IP54
Enclosure IP00
4 4
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V)
[A]
Continuous KVA (at 550 V) [KVA]
Continuous KVA (at 575 V) [KVA]
Continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V ) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
Max. cable size, mains, motor and load
share [mm 2 (AWG)
Max. cable size, brake [mm
Max. external mains fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
Weight, enclosure IP21, IP54 [kg]
Weight, enclosure IP00 [kg]
Efficiency 4)
Output frequency
Heatsink overtemp. trip
Power card ambient trip
* High overload=160% torque during 60 s, Normal overload=110% torque during 60 s.
Table 4.9 Technical Specifications, E-frame 525-690 V Mains Supply 3x525-690 V AC
1) American Wire Gauge.
2) For fuse ratings, see 7.2.1 Fuses.
3) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the frequency converter. If the
switching frequency is raised from nominal, the power losses rise significantly. LCP and typical control card power consumptions are included.
Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each add
only 4 W.
4) Measured using 5 m screened motor cables at rated load and rated frequency.
64
VLT
1) ]
2 1)
(AWG) ]
2)
3)4) 4795
3)4) 4970
®
AutomationDrive FC 300 Design Guide 90-1200 kW
P400
HO NO
315 400
400 500
400 500
E1
E1
E2
429 523
644 575
410 500
615 550
409 498
408 498
490 598
413 504
395 482
395 482
4x240 (4x500 mcm)
2x185 (2x350 mcm)
700
6010 6493
6239 6707
263
221
± 15% (tolerance relates to variety in voltage and cable conditions.) These
MG34S202 - Rev. 2013-08-19
P500
HO NO HO
400 450 450
500 600 600
500 560 560
E1
E1
E2
523 596 596
785 656 894
500 570 570
750 627 855
498 568 568
498 568 568
598 681 681
504 574 574
482 549 549
482 549 549
4x240 (4x500 mcm) 4x240 (4x500 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
900
7395 7383
7653 7633
272
236
0.98
0-500 Hz
110 °C
85 °C
P560
NO
500
650
630
E1
E1
E2
630
693
630
693
600
627
753
607
607
607
900
8209
8495
313
277