HP FlexNetwork HSR6600 Configuration Manual page 551
Comware 7 mpls
Hide thumbs
Also See for FlexNetwork HSR6600:
- Command reference manual (542 pages) ,
- Troubleshooting manual (41 pages) ,
- Security configuration manual (559 pages)
Table of Contents
Advertisement
Interface
: InLoop0
Destination: 2012::/64
NextHop
: FE80::20C:29FF:FE40:701
Interface
: GE1/1/2
Destination: FE80::/10
NextHop
: ::
Interface
: NULL0
Destination: FF00::/8
NextHop
: ::
Interface
: NULL0
The output shows that the MCE has learned the private route of VPN 2 through RIPng. The
MCE maintains the routes of VPN 1 and VPN 2 in two different routing tables. In this way, routes
from different VPNs are separated.
3.
Configure routing between the MCE and PE 1:
# The MCE is connected to PE 1 through subinterfaces. On the MCE, bind subinterface
GigabitEthernet 1/1/3.1 to the VPN instance vpn1.
[MCE] interface gigabitethernet 1/1/3.1
[MCE-GigabitEthernet1/1/3.1] ip binding vpn-instance vpn1
# Configure the subinterface to terminate VLAN 10.
[MCE-GigabitEthernet1/1/3.1] vlan-type dot1q vid 10
# Configure an IPv6 address for the subinterface.
[MCE-GigabitEthernet1/1/3.1] ipv6 address 2001:2::3 64
[MCE-GigabitEthernet1/1/3.1] quit
# On the MCE, bind subinterface GigabitEthernet 1/1/3.2 to the VPN instance vpn2.
[MCE] interface gigabitethernet 1/1/3.2
[MCE-GigabitEthernet1/1/3.2] ip binding vpn-instance vpn2
# Configure the subinterface to terminate VLAN 20.
[MCE-GigabitEthernet1/1/3.2] vlan-type dot1q vid 20
# Configure an IPv6 address for the subinterface.
[MCE-GigabitEthernet1/1/3.2] ipv6 address 2002:2::3 64
[MCE-GigabitEthernet1/1/3.2] quit
# On PE 1, bind subinterface GigabitEthernet 1/1/1.1 to the VPN instance vpn1.
[PE1] interface gigabitethernet 1/1/1.1
[PE1-GigabitEthernet1/1/1.1] ip binding vpn-instance vpn1
# Configure the subinterface to terminate VLAN 10.
[PE1-GigabitEthernet1/1/1.1] vlan-type dot1q vid 10
# Configure an IPv6 address for the subinterface.
[PE1-GigabitEthernet1/1/1.1] ipv6 address 2001:2::4 64
[PE1-GigabitEthernet1/1/1.1] quit
# On PE 1, bind subinterface GigabitEthernet 1/1/1.2 to the VPN instance vpn2.
[PE1] interface gigabitethernet 1/1/1.2
[PE1-GigabitEthernet1/1/1.2] ip binding vpn-instance vpn2
# Configure the subinterface to terminate VLAN 20.
[PE1-GigabitEthernet1/1/1.2] vlan-type dot1q vid 20
541
Cost
: 0
Protocol
: RIPng
Preference: 100
Cost
: 1
Protocol
: Direct
Preference: 0
Cost
: 0
Protocol
: Direct
Preference: 0
Cost
: 0
Advertisement
Table of Contents
