Subscribe to Our Youtube Channel
Related Manuals for HP FlexNetwork HSR6802
Summary of Contents for HP FlexNetwork HSR6802
-
Page 1: Installation Guide
HPE FlexNetwork HSR6800 Routers Installation Guide Part number: 5200-3525 Document version: 6W105-20170412... - Page 2 © Copyright 2015, 2017 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
-
Page 3: Table Of Contents
Contents Preparing for installation ···································································· 1 Safety recommendations ············································································································· 1 Safety symbols ··················································································································· 1 Electricity safety ·················································································································· 1 Laser safety ······················································································································· 1 Router moving ···················································································································· 2 ESD prevention ··················································································································· 2 Examining the installation site ······································································································· 3 Weight support ··················································································································· 3 Temperature and humidity ·····································································································... - Page 4 Overview ························································································································· 33 Connecting a T3 cable ········································································································ 33 Accessing the router ······································································· 35 Login methods ························································································································ 35 Logging in through the console port ····························································································· 35 Setting up a configuration environment ·················································································· 35 Setting terminal parameters ································································································· 36 Powering on the router ·············································································································· 38 Verifying before power-on ···································································································...
- Page 5 RUN LED fast flashes ········································································································ 61 ALM LED is steady on or flashes ·························································································· 61 PALM LED is steady on ······································································································ 62 LPU failures ···························································································································· 62 RUN LED is off ················································································································· 62 RUN LED fast flashes ········································································································ 63 Power supply failures ················································································································ 63 Power LED is off ···············································································································...
- Page 6 FIP-300 ··························································································································· 98 FIP-310 ··························································································································· 99 FIP-600 ························································································································· 101 SAP-48GBE ··················································································································· 102 SAP-24GBP ··················································································································· 102 SAP-48GBP ··················································································································· 103 SAP-4EXP ····················································································································· 104 SAP-20GE2XP ··············································································································· 105 SAP-28GE ····················································································································· 106 SPEs/OAPs ·························································································································· 107 HIMs/MIMs ··························································································································· 107 Transceiver modules ·············································································································· 108 Lightning protector for a port ····································································································· 108 Power strip with lightning protection ···························································································...
-
Page 7: Preparing For Installation
Preparing for installation Safety recommendations To avoid any equipment damage or bodily injury caused by improper use, read the following safety recommendations before installation. Note that the recommendations do not cover every possible hazardous condition. Safety symbols When reading this document, note the following symbols: WARNING means an alert that calls attention to important information that if not understood or followed can result in personal injury. -
Page 8: Router Moving
metallic board hole or bending along the acute side of mechanical parts, the fiber must wear jackets or cushions. Router moving CAUTION: Do not hold the handle of the fan tray or power supply, the handle of the rear cover of the chassis, or the air vents of chassis. -
Page 9: Examining The Installation Site
Figure 1 Attaching an ESD wrist strap (1) ESD wrist strap (2) Lock (3) ESD plug Examining the installation site The routers can only be used indoors. To make sure the router operates correctly and to prolong its service lifetime, the installation site must meet the following requirements: Weight support Make sure the floor can support the total weight of the router and accessories (such as the rack and HIMs/MIMs). -
Page 10: Altitude
Table 1 Temperature requirements Item Temperature Operating Temperature 0°C to 45°C (32°F to 113°F) Storage Temperature –40°C to +70°C (–40°F to +158°F) Table 2 Humidity requirements Item Humidity Operating humidity (noncondensing) 10% RH to 95% RH Storage humidity (noncondensing) 5% RH to 95% RH Altitude Table 3 Altitude requirements Item... -
Page 11: Cooling System
Cooling system Fan trays of the routers are hot swappable and support automatic fan speed adjustment. To ensure good ventilation, the following requirements must be met: • Leave a minimum clearance of 10 cm (3.94 in) at the inlet and outlet air vents. •... -
Page 12: Emi
All electromagnetic interference (EMI) sources, from outside or inside of the router and application system, adversely affect the router in the following ways: • A conduction pattern of capacitance coupling. • Inductance coupling. • Electromagnetic wave radiation. • Common impedance (including the grounding system) coupling. To prevent EMI, use the following guidelines: •... -
Page 13: Power Supply
Table 6 Router dimensions and rack requirements Model Chassis dimensions Rack requirements • Height—220 mm (8.66 in)/5 RU • A minimum of 95 mm (3.74 in) • Width—436 mm (17.17 in) between the front rack posts and the • Depth—576 mm (22.68 in) front door. - Page 14 Product code Item Quantity Grounding cable 5185-8507 Mounting bracket kit: • Mounting brackets • HSR6802: 5189-9473 and 5003-2441 • HSR6804: 5189-9472 and 1 set 5003-2440 • HSR6808: 5003-1608 • M4 countersunk head screw • M6 cage nut: M6 screw and cage nut •...
-
Page 15: Installing The Router
Installing the router Installation flow Figure 4 Installation flow Installing a cable management bracket The cable management brackets of the HSR6802 and HSR6804 are provided with mounting brackets. You need to install a cable management bracket for an HSR6808 router. To install a cable management bracket: Face the front of the router. -
Page 16: Installing The Router In A 19-Inch Rack
Figure 5 Installing a cable management bracket Installing the router in a 19-inch rack The procedures for installing an HSR6800 router in a rack are similar. This section uses an HSR6802 router as an example. To install the router in a rack, you need mounting brackets and a rack shelf. Installing cage nuts to the rack Locate the installation position for the router and then install a rack shelf to the rack. -
Page 17: Attaching The Mounting Brackets To The Router
Figure 6 Marking the positions of cage nuts Insert one edge of a cage nut into the hole. Use a flat-blade screwdriver to compress the other edge of the cage nut, and then push the cage nut fully into the hole. Repeat steps 3 and 4 to install other cage nuts to all the marked positions on the rack post. -
Page 18: Installing The Router In A 19-Inch Rack
Figure 8 Attaching the front mounting brackets to the two sides of the router Installing the router in a 19-inch rack Put the router on the rack shelf. Slide the router into the rack so the screw holes on the mounting brackets are aligned with holes that are installed with cage nuts on the rack posts. -
Page 19: Installing A Power Supply
Attach the grounding screw to the ring terminal of the grounding cable. Use a Phillips screwdriver to fasten the grounding screw into the grounding screw hole. Connect the other end of the grounding cable to the grounding strip of the rack. Figure 10 Connecting the grounding cable to the grounding hole of router IMPORTANT: •... -
Page 20: Installing An Mpu And A Switching Fabric Module
Figure 11 Installing a power supply Installing an MPU and a switching fabric module Installing an MPU CAUTION: The RUN LED flashes fast when the MPU is starting up. Do not install or remove the MPU during this period to avoid hardware damage. Before the installation, make sure the ejector levers of the MPU are outwards. -
Page 21: Installing An Lpu
Loosen the captive screws with a Phillips screwdriver to remove the filler panel from the slot. Keep the removed filler panel for future use. Insert the SFE-X1 slowly along the slide rails until positioning pins on the backplane are seated in the positioning holes, and then push the ejector levers inward to lock the SFE-X1 in position. -
Page 22: Installing A Him
Loosen the captive screws with a Phillips screwdriver to remove the filler panel from the slot. Keep the removed filler panel for future use. Skip this step if you install the FIP-210 to Slot 3 of the HSR6802/HSR6804, or Slot 7 of the HSR6808. -
Page 23: Installing A Mim
Figure 15 Installing a HIM Installing a MIM The procedures for installing MIMs are similar. This example installs a MIM to a FIP-210. To install a MIM: Face the front of the router and locate the slot to install the MIM on the FIP-210. The MIM should be installed in the lower slot on the FIP-210. -
Page 24: Installing Optional Components
Insert the CF card into the slot following the direction shown in Figure 17, and make sure it does not project from the slot. Figure 17 Inserting the CF card into the slot Installing optional components Optional components (including the air filter and lightning protectors) are not provided with the router. Purchase them if necessary. - Page 25 Figure 19 Inserting the air filter to the slide rail Use a Phillips screwdriver to fasten the captive screws on the rear side of the air filter. Figure 20 Fastening the captive screws Installing an air filter on an HSR6808 Face the front of the router.
-
Page 26: Installing A Lightning Protector For A Network Port
Figure 21 Installing an air filter on an HSR6808 Installing a lightning protector for a network port Read the instructions for the lightning protector carefully before you install it. The lightning protector for a network port is only applicable to a copper Ethernet port. If part of the network cable of a copper Ethernet port must be routed outdoors, connect a lightning protector to the cable before you plug the cable into the port. -
Page 27: Connecting The Ac Power Supply To A Power Strip With Lightning Protection
Figure 22 Installing a lightning protector for a network port (1) Grounding cable (2) Lightning protector Installation precautions The performance of the port lightning protector might be affected in the following cases: • The port lightning protector is installed in reverse direction. Connect the IN end to the outdoor network cable and the OUT end to the network port on the router. -
Page 28: Installing A Surge Protector
If the red LED is on, use a multimeter to check the polarity of the wires in the power socket for wrong connections. If the zero wire (left) and the live wire (right) are correctly connected, check for missing grounding connection. Figure 23 Power strip with lightning protection On means the circuit is operating correctly. - Page 29 The router supports the following types of surge protectors: • Surge protector—Maximum discharge current 2.5KA/protection voltage 25V--SMB-75J/ SMB-75J-1W-10Mbps • Surge protector—Maximum discharge current 2.5KA/protection voltage 25V-BNC-75K/ BNC-75K-10Mbps • Surge protector (U port)—Maximum discharge current 3KA/common-mode 400V/differential mode 170V-RJ11 To install a surge protector: Use a double-faced adhesive tape to stick the surge protector onto the router chassis, and make sure it is as close to the grounding screw of the router as possible.
-
Page 30: Connecting The Power Cord
• The installed surge protectors are not sufficient. If the router has more than one cable connected with other devices through cables outdoor, install a surge protector for each cable. Connecting the power cord Connecting an AC power cord Make sure the router is reliably grounded, and the power switch on the router is in the OFF position. - Page 31 Put the protection cover on the wiring terminals. Connect the other ends of the wires to the DC power source wiring terminals, with the negative wire (– or L–) to the negative terminal (–) and the positive wire (+ or M/N) to the positive terminal (+).
- Page 32 Insert one end of the wire marked with “+” into the terminal marked with “+”, and fasten the screw to fix the cord. Figure 28 Attaching the wires to the terminal block Correctly orient the terminal block and insert it into the power supply, and fasten the captive screws with a Phillips screwdriver.
-
Page 33: Connecting Interface Cables
Connecting interface cables Connecting the AUX cable Overview An AUX cable has a crimped RJ-45 connector at one end for connecting to the AUX port of the router, and D9 male connectors at the other end for connecting to the serial port of the modem. Figure 30 AUX cable Connecting the AUX cable Plug the D9 male connector at one end of the AUX cable into the serial port on the modem. -
Page 34: Connecting An Ethernet Cable
Connecting an Ethernet cable Overview 10/100 Mbps Ethernet uses category-5 twisted pair cables, while 1000 Mbps Ethernet uses category-5 enhanced or category-6 twisted pair cables. Twisted pair cables include straight-through cables and crossover cables. Category-5 cables provide a transmission frequency of 100 MHz for voice and data transmission; they are mainly used in 100Base-T and 10Base-T networks. -
Page 35: Making An Ethernet Cable
Table 8 Straight-through cable pinouts Pinout No. Orange/white Orange/white Orange Orange Green/white Green/white Blue Blue Blue/white Blue/white Green Green Brown/white Brown/white Brown Brown Table 9 Crossover cable pinouts Pinout No. Orange/white Green/white Orange Green Green/white Orange/white Blue Blue Blue/white Blue/white Green Orange Brown/white... -
Page 36: Connecting A Fiber Cable
Ethernet port of the peer device. The 10/100/1000Base-T copper ports of the router support MDI/MDI-X auto-sensing. They are connected to the network through category-5 or above twisted pairs that are equipped with RJ-45 connectors. Examine the status LED of the Ethernet ports. For more information about the LED status, see "Appendix B LEDs."... -
Page 37: Fiber Cable Overview
Fiber cable overview CAUTION: • Never exert a fierce force when you insert or remove a fiber connector. • Never pull, press, or extrude the fiber fiercely. Optical fibers can be classified into single-mode optical fibers and multi-mode optical fibers. A single-mode optical fiber carries only a single ray of light, and a multi-mode optical fiber carries multiple modes of lights. -
Page 38: Connecting A Fiber Cable
Figure 36 LC connector (1) LC connector (2) Optical fiber Connecting a fiber cable WARNING! Do not stare into any fiber port when you connect an optical fiber. The laser light emitted from the optical fiber might hurt your eyes. To connect a fiber cable: Remove the dust plug from a fiber port of the router. -
Page 39: Connecting A T3 Cable
Figure 37 Connecting a fiber cable Examine the LINK LED after connection. If the LED is on, the optical fiber link is present. If the LED is off, no link is present. This might be because the TX and Rx port of the optical fiber are not connected correctly. - Page 40 Figure 39 Connecting a T3 cable...
-
Page 41: Accessing The Router
Accessing the router Login methods The following logins methods are available for you to log in to the router: • Logging in through the console port, which is the most common way to log in to a router and also the prerequisite for configuring other login methods. •... -
Page 42: Setting Terminal Parameters
Setting terminal parameters Select Start > All Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box appears. Figure 41 Connection description Select the serial port to be used from the Connect using list, and click OK. Figure 42 Setting the serial port used by the HyperTerminal connection Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None, and click OK. - Page 43 Figure 43 Setting the serial port parameters Select File > Properties in the HyperTerminal window. Figure 44 HyperTerminal window On the Settings tab, set the emulation to VT100 and click OK.
-
Page 44: Powering On The Router
Figure 45 Setting terminal emulation in test Properties dialog box Powering on the router Verifying before power-on Before powering on the router, verify the following items: • The power supplies and fan trays are correctly installed. • The power cord and grounding cable are correctly connected. •... -
Page 45: Logging In To The Router Through Telnet/Ssh
Press Ctrl+T to start memory test Booting Normal Extended BootWare The Extended BootWare is self-decompressing.......Done. **************************************************************************** HPE Router BootWare, Version 2.04 **************************************************************************** Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP Compiled Date : Nov 6 2016 CPU Type : P2020 CPU L1 Cache : 32KB CPU Clock Speed... -
Page 46: Logging In To The Router Through The Aux Port
Logging in to the router through the AUX port After powering on the router, connect the console cable to the console port. To configure the AUX port: Step Command Enter system view. system-view Enter AUX user interface view. user-interface aux 0 Set the authentication mode. -
Page 47: Replacement Procedures
Replacement procedures The router uses modular design. All modules for the router are hot swappable. Safety recommendations • Always wear an ESD wrist strap or ESD gloves when you replace the modules. • To hot swap an LPU or HIM/MIM, first use the remove command to stop the card from operating. -
Page 48: Replacing An Mpu
• If the router is installed with two MPUs, make sure both MPUs operate correctly before replacement. As a best practice to replace the active MPU, execute the slave switchover command in the system view of the active MPU to trigger an active and standby switchover. For more information about the slave switchover command, see HPE FlexNetwork HSR6800 Routers High Availability Command Reference. -
Page 49: Replacing An Lpu
Figure 48 Pulling the SFE-X1 out of the slot (HSR6808) Install a new SFE-X1. For the installation procedure, see "Installing an SFE-X1 switching fabric module." If you do not install a new SFE-X1 in the slot, install a filler panel. Replacing an LPU CAUTION: To avoid hardware damage, do not replace the LPU when its RUN LED is fast flashing. -
Page 50: Replacing A Him
Figure 49 Pulling the FIP module out of the slot Install a new FIP module. For the installation procedure, see "Installing an LPU." If you do not install a new FIP module in the slot, install a filler panel. Replacing a HIM Face the front of the router and locate the HIM to be removed. -
Page 51: Replacing A Cf Card
Figure 51 Pulling the MIM out of the slot Install a new MIM. For the installation procedure, see "Installing a MIM." If you do not install a new MIM in the slot, install a filler panel. Replacing a CF card CAUTION: To avoid hardware damage, do not remove the CF card when the router is booting or the CF LED is flashing. -
Page 52: Replacing A Fan Tray
Put the dust plug on the removed module, and put the removed module into its original shipping materials. Install a new transceiver module. For the installation procedure, see "Connecting a fiber cable." If you do not install a new transceiver module in the interface, install a dust-proof plug in the interface. -
Page 53: Replacing A Fan Tray For An Hsr6808 Router
Figure 54 Pulling out the fan tray Holding the handle of the fan tray with one hand and supporting the bottom of the fan tray with the other hand, gently push the fan tray into the slot along the slide rails until it is completely seated. -
Page 54: Replacing An Air Filter For An Hsr6802/Hsr6804 Router
Replacing an air filter for an HSR6802/HSR6804 router Face the left side of the router. Use a Phillips screwdriver to completely loosen the captive screws of the air filter. Figure 56 Loosening the captive screws of the air filter Gently pull the air filter out along the slide rails. Figure 57 Pulling the air filter out along the slide rails Install a new air filter. -
Page 55: Replacing A Memory Module
Figure 58 Removing the air filter Install a new air filter. For the installation procedure, see "Installing an air filter on an HSR6808." Replacing a memory module CAUTION: For the router to operate correctly, use the memory modules provided by Hewlett Packard Enterprise only. -
Page 56: Replacing A Memory Module
Figure 60 Memory module structure (DDR3) (1) Connector edge (2) Polarization notch (3) Latch notch Replacing a memory module The methods for replacing memory modules are similar. This example replaces a memory module on an RSE-X2. To replace a memory module: Pull the release latches away from the memory module at both ends so that the memory module is lifted from the memory module slot. -
Page 57: Hardware Management And Maintenance
Hardware management and maintenance The output depends on your router model and software version. For more information about the commands used in this chapter, see HPE FlexNetwork HSR6800 Routers Command References. Displaying the hardware information of the router Displaying the version information of the router Use the display version command to display software and hardware version information of the router. -
Page 58: Displaying Detailed Information About A Card
===============display clock=============== ================================================= 08:54:16 UTC Fri 15/06/2012 =================================================== ===============display version=============== =================================================== … Displaying detailed information about a card • Use the display device verbose command to display detailed information about all cards. <Sysname>display device verbose System-mode(Current/After Reboot): Normal/Normal Slot No. Board type Status Primary... -
Page 59: Displaying The Electrical Label Data
Displaying the electrical label data Electrical label data is also called permanent configuration data or archive information, which includes the card name, serial number, MAC address, and vendor name. • Use the display device manuinfo command to display the electrical label data for the card in each slot. -
Page 60: Displaying The Mpu Memory Usage
Field Description After a boot, the system calculates and records the average CPU usage rate every one minute. 1% in last 1 minute This field displays the average CPU usage rate in the last minute. After a boot, the system calculates and records the average CPU usage rate every five minutes. -
Page 61: Displaying The Fan Operating Status
Displaying the fan operating status Use the display fan command to display the fan operating status. <Sysname> display fan 1 State: Normal Table 17 Command output Field Description Number of the fan. Fan state: • Normal—The fan is operating correctly. State •... -
Page 62: Displaying The Alarming Thresholds Of A Card
Displaying the alarming thresholds of a card Use the display environment command to display the temperature information and alarming thresholds of a card. <Sysname> display environment Temperature information (degree centigrade): ---------------------------------------------------------- SlotNo Temperature Lower limit Upper limit Table 19 Command output Field Description SlotNo... -
Page 63: Displaying And Verifying Transceiver Modules
Description: GigabitEthernet5/0/0 Interface The Maximum Transmit Unit is 1500 Internet protocol processing : disabled IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 2222-2222-2122 IPv6 Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 2222-2222-2122 Media type is twisted pair, loopback not set, promiscuous mode not set …... -
Page 64: Active And Standby Switchover For Mpus
To display the alarming information or fault detection parameters of a transceiver module: Task Command Remarks Display the current alarm display transceiver alarm Available for all transceiver information of the transceiver interface [ interface-type modules. module in a specified interface. interface-number ] For more information about the transceiver module displaying commands, see HPE FlexNetwork HSR6800 Routers Command References. -
Page 65: Displaying The Exception Handling Method
• maintain—Maintaining the current status of the failed MPU so that the system does not take any restoration measures. Some software faults are hard to reproduce, and the printed information will be lost after the router reboots. In this case, you can maintain the current status of the router, facilitating fault location. - Page 66 Task Command Remarks Available in user view. Reboot the router or the card in reboot [ slot If you do not specify the slot keyword, the the specified slot immediately. slot-number ] command reboots the router, including the active MPU, standby MPU, and the LPUs. To schedule a reboot: Task Command...
-
Page 67: Troubleshooting
Troubleshooting IMPORTANT: The barcode stuck on the router chassis contains production and servicing information. Before you return a faulty router for serving, provide the barcode information of the router to Hewlett Packard Enterprise Support. MPU failures RUN LED is off Symptom The RUN LED for the MPU is off. -
Page 68: Palm Led Is Steady On
PALM LED is steady on Symptom The PALM LED for the MPU is steady on. For more information about MPU LEDs, see Table Solution To resolve the problem: Verify that the power supply and power consumption match. For example, if an HSR6808 is installed with a 650 W power supply but two SAP-48GBE modules, the power available is not sufficient for the whole power consumption and one SAP module cannot be powered on. -
Page 69: Run Led Fast Flashes
%Apr 26 16:46:32:169 2012 HPE DRVMSG/1/InSufficientPwr: No sufficient power, failed to power on slot 3. Execute the display version command to verify that the LPU is in position: Slot3: The Board is present, state is unknown If the problem persists, contact Hewlett Packard Enterprise Support. RUN LED fast flashes Symptom 20 minutes after the router is powered on or the LPU is inserted into the router, the RUN LED for the... -
Page 70: Red Power Led Is On
Red power LED is on Symptom The router cannot be powered on and the red power LED on the front panel is on. Solution To resolve the problem:: Turn off the power switch, and verify that the power supply is firmly seated. Verify that the power source meets the requirements of the router. -
Page 71: Him/Mim Failures
HIM/MIM failures Symptom When a HIM/MIM is hot swapped, the output from the configuration terminal shows that the HIM/MIM is faulty or the router cannot recognize the HIM/MIM. %Jun 14 11:12:36:037 2012 HPE DRVICOUT/1/DrvIcOutStr: -Slot=4; Card in Slot 4 Sublot 1 can not be recognized ! Solution To resolve the problem: Verify that the HIM/MIM is firmly seated. -
Page 72: No Response From The Serial Port
Solution To resolve the problem: Verify that the Data bits field is set to 8 for the console terminal. If the Data bits field is set to 5 or 6, the console terminal will display garbled characters. Verify that the Bits per second field is set to 9600 bps. An incorrect Bits per second might also cause the configuration terminal to display garbled characters. -
Page 73: Examining The State Of Password Recovery Capability
Figure 62 Dealing with password loss Examining the state of password recovery capability Reboot the router. System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Press Ctrl+T to start memory test Booting Normal Extend BootWare..---- More ---- Press Ctrl + B within three seconds after the "Press Ctrl+B to enter extended boot menu..." prompt message appears. -
Page 74: Dealing With Console Login Password Loss When Password Recovery Capability Is Enabled
Ctrl+Z: Access EXTEND-ASSISTANT MENU Ctrl+F: Format File System Enter your choice(0-9): Dealing with console login password loss when password recovery capability is enabled Reboot the router to access the EXTEND-BOOTWARE menu, and then enter 6. The current mode is password recovery. Note: The current operating device is cfa0 Enter <... -
Page 75: Dealing With User Privilege Level Password Loss When Password Recovery Capability Is Enabled
[HPE] save Dealing with user privilege level password loss when password recovery capability is enabled Reboot the router to access the EXTEND-BOOTWARE menu, and then enter 8. The current mode is password recovery. Note: The current operating device is cfa0 Enter <... -
Page 76: Cooling System Failure
===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System |<2> Enter Serial SubMenu |<3> Enter Ethernet SubMenu |<4> File Control |<5> Restore to Factory Default Configuration |<6> Skip Current System Configuration |<7> BootWare Operation Menu |<8> Clear Super Password |<9> Storage Device Operation |<0> Reboot ============================================================================ Ctrl+Z: Access EXTEND-ASSISTANT MENU Ctrl+F: Format File System... -
Page 77: Ethernet Port Failure
s 0, slotIndex 0.1 %Jun 14 11:56:48:279 2012 HPE DEVM/4/BOARD_TEMP_TOOHIGH: Board temperature changes to normal on Chassis 0 Slot 1, type is RSE-X2. The output shows that the operating temperature of the router restores to normal state. When exceptions occur, the temperature inside the router might exceed the critical temperature threshold, and the following information appears on the configuration terminal in this case: %Jun 14 12:06:58:436 2012 HPE DRVMSG/3/TempCritical: CPU temperature is greater than alarm upper limit in slot 1, index is 1... -
Page 78: Software Upgrade Failures
Use the display command to verify that the interface of the HIM/MIM has been correctly configured and is operating correctly. If the problem persists, contact Hewlett Packard Enterprise Support. Software upgrade failures No response from the serial port of the MPU Symptom The serial port of the MPU gives no response. -
Page 79: System Software Image File Missing Errors
150 "xxx" file ready to send (xxx bytes) in ASCII mode FTP: Error Writing Local File(Screen). • The file to be downloaded is not found. 227 Entering Passive Mode (192,168,1,10,10,203) 550 Error: File xxx does not exist FTP: Error Writing Local File(Screen). •... -
Page 80: Network Topology Icons
Port numbering in examples The port numbers in this document are for illustration only and might be unavailable on your device. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic text represents arguments that you replace with actual values. Italic Square brackets enclose syntax choices (keywords or arguments) that are optional. - Page 81 Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features. Represents an access controller, a unified wired-WLAN module, or the access controller engine on a unified wired-WLAN switch.
-
Page 82: Support And Other Resources
Hewlett Packard Enterprise Support Center More Information on Access to Support Materials page: www.hpe.com/support/AccessToSupportMaterials IMPORTANT: Access to some updates might require product entitlement when accessed through the Hewlett Packard Enterprise Support Center. You must have an HP Passport set up with relevant entitlements. -
Page 83: Websites
Websites Website Link Networking websites Hewlett Packard Enterprise Information Library for www.hpe.com/networking/resourcefinder Networking Hewlett Packard Enterprise Networking website www.hpe.com/info/networking Hewlett Packard Enterprise My Networking website www.hpe.com/networking/support Hewlett Packard Enterprise My Networking Portal www.hpe.com/networking/mynetworking Hewlett Packard Enterprise Networking Warranty www.hpe.com/networking/warranty General websites Hewlett Packard Enterprise Information Library www.hpe.com/info/enterprise/docs Hewlett Packard Enterprise Support Center... - Page 84 part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page.
-
Page 85: Appendix A Chassis Views And Technical Specifications
(RMN). These regulatory numbers should not be confused with the marketing name HPE HSR6800, or product codes. Table 22 HPE HSR6800 router models Product code Description Abbreviation HPE FlexNetwork HSR6802 JG361B BJNGA-BB0002 HSR6802 Router chassis HPE FlexNetwork HSR6804 JG362B... -
Page 86: Chassis Views
HPE FlexNetwork HSR6800 1200W DC Power Supply PSR1200-D Table 27 Fan tray models Product code Description Alias JG367A HPE FlexNetwork HSR6802 Router Spare Fan Assembly HSR6802 Fan JG368A HPE FlexNetwork HSR6804 Router Spare Fan Assembly HSR6804 Fan JG369A HPE FlexNetwork HSR6808 Router Spare Fan Assembly... -
Page 87: Hsr6802
HSR6802 Figure 63 HSR6802 front view (1) MPU slots (Slot 0 and Slot 1) (2) Fan tray (4) Line processing unit (LPU) or switching fabric module (3) Power supply slots slots (Slot 2 and Slot 3) Figure 64 HSR6802 rear view (1) Rear cover handle (2) Chassis handle (3) Grounding screw and sign... -
Page 88: Hsr6804
HSR6804 Figure 65 HSR6804 front view (1) MPU slots (Slot 0 and Slot 1) (2) Fan tray (4) LPU or switching fabric module slots (Slot 2 to (3) Power supply slots Slot 5) Figure 66 HSR6804 rear view (1) Rear cover handle (2) Chassis handle (3) Grounding screw and sign (4) Air vents... -
Page 89: Hsr6808
HSR6808 Figure 67 HSR6808 front view (1) Fan tray (2) Cable management bracket (3) Switching fabric module or LPU slots (Slot 0 to (4) MPU slots (Slot 4 and Slot 5) Slot 3 and Slot 6 to Slot 9) (5) Air inlet vents (An optional air filter can be (6) Power supply slots installed.) -
Page 90: Dimensions And Weights
Figure 68 HSR6808 rear view (1) Chassis air exhaust vents (2) Chassis handle (3) Rear cover handle (4) Grounding screw and sign (5) Power supply air exhaust vents Dimensions and weights Table 28 Router dimensions and weights Item HSR6802 HSR6804 HSR6808 886 mm (34.88 in) (20 Height (H) -
Page 91: Power Consumption
Model Net weight Dimensions (H × W × D) SFE-X1 3.25 kg (7.16 lb) 45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in) FIP-110 3.25 kg (7.16 lb) 45 × 399 × 412 mm (1.77 × 15.71 × 16.22 in) FIP-210 3.35 kg (7.39 lb) 45 ×... -
Page 92: Power Supplies
Model Power consumption RT-FAN-6608-X 20.20 W to 109 W RT-FAN-6616-X 65.46 W to 262.8 W Power supplies CAUTION: • Do not install AC and DC power supplies on the same router. • Power supplies installed on a router must be the same model. The HSR6800 routers support AC and DC power supplies. -
Page 93: Dc Power Supplies
PSR1200-A Figure 70 PSR1200-A view (1) AC-input power receptacle (2) Power switch (3) Handle (4) Power supply status LED Table 33 PSR1200-A specifications Item Remarks Rated input voltage 100 VAC to 240 VAC @ 50 or 60 Hz Maximum input current 16 A Maximum power 1213 W... - Page 94 Table 34 PSR650-D specifications Item Remarks Rated input voltage –48 VDC to –60 VDC Maximum input current 25 A Maximum power 650 W PSR1200-D Figure 72 PSR1200-D view (1) Power supply connector (2) Power switch (3) Handle (4) Power supply status LED Table 35 PSR1200-D specifications Item Remarks...
-
Page 95: Fan Trays
Fan trays Figure 73 Fan tray for the HSR6802 Figure 74 Fan tray for the HSR6804 (1) Fan (2) Fan tray status LED (RUN) (3) Alarm LED (ALM) (4) Handle (5) Rotating blade hazard label... -
Page 96: Mpus
NOTE: The fan tray structure for the HSR6802 is similar with the fan tray structure for the HSR6804. Figure 75 Fan tray for the HSR6808 (1) Fan (2) Alarm LED (ALM) (3) Fan tray status LED (RUN) (4) Fan tray release button (5) Rotating blade hazard label Table 36 Fan tray specifications Fan tray... - Page 97 RSE-X2 front panel Figure 76 RSE-X2 front panel (1) Management Ethernet port (MANAGEMENT) (2) AUX port (AUX) (3) MPU status LEDs (4) Reset button (RESET) (5) USB port (6) Console port (CONSOLE) (7) CF card slot (8) CF card button (9) CF card status LED RSE-X2 specifications Item...
-
Page 98: Components
Components CF card CAUTION: Use CF cards provided by Hewlett Packard Enterprise only. The router might be incompatible with other CF cards. A compact flash (CF) card stores logs, system software image files, and configuration files. The router is equipped with a built-in CF card, which is identified with cfa0. In addition, the router provides an external CF card slot to expand the storage space. -
Page 99: Reset Button
NOTE: The dialup function for an AUX port is supported only on Comware 5. For MPU and Comware compatibility, see "MPU and Comware compatibility matrix." Management Ethernet port The management Ethernet port is a 10Base-T/100Base-TX/1000Base-T autosensing RJ-45 port. It allows you to upgrade software and manage the router through a network management server without using any service interface of the router. -
Page 100: Switching Fabric Module
Switching fabric module SFE-X1 The SFE-X1 is specially designed for the HSR6800 by Hewlett Packard Enterprise to improve the router's switching capability. An HSR6800 supports SFE-X1 switching fabric modules only when an RSE-X2 MPU is installed. Front panel Figure 77 SFE-X1 front panel (1) Captive screw (2) Ejector lever (3) Switching fabric module status LED (RUN) -
Page 101: Fip-110
FIP-110 Front panel Figure 78 FIP-110 front panel (1) Slot 4 (2) Slot 3 (3) Combo interface 1 (4) Combo interface 0 (5) Slot 1 (6) Slot 2 (7) OPEN BOOK mark Technical specifications Item Specification Flash 4 MB • Default—Two 1-GB DDR2 SDRAMs Memory type and size •... -
Page 102: Fip-210
Table 42 FIP-110 fiber Ethernet port specifications Item Specification Connector Transceiver module type Interface standards 802.3, 802.3u, and 802.3ab Duplex mode 1000 Mbps, full duplex Available interface modules Table 43 Maximum number of MIM and HIMs supported by routers fully configured with FIP-110 modules FIP/Interface module HSR6802... -
Page 103: Fip-240
Item Specification 10 Mbps, half/full-duplex 2 copper ports (MDI/MDIX 100 Mbps, half/full-duplex autosensing) 1000 Mbps, full-duplex 2 fiber ports 1000 Mbps, full-duplex 2 supported 2 supported Hardware encryption Supported Hot swapping Supported Combo interface specifications Specifications of combo interfaces on the FIP-210 and the FIP-110 are the same. For more information, see Table 41 Table... -
Page 104: Fip-300
Item Specification • Default—One 2-GB DDR3 SDRAM Memory type and size • Maximum—Two 2-GB DDR3 SDRAMs NVRAM 128 KB 10 Mbps, half/full-duplex 2 copper ports (MDI/MDIX Combo interface 100 Mbps, half/full-duplex autosensing) 1000 Mbps, full-duplex 2 fiber ports 1000 Mbps, full-duplex 4 supported 2 full-height or 4 half-height HIMs supported NOTE:... -
Page 105: Fip-310
Technical specifications Item Specification Flash 8 MB • Default—Two 2-GB DDR3 SDRAMs • Maximum—Two 2-GB DDR3 SDRAMs Memory type and size Install the DDR3 SDRAMs in subslots 1 and 3 in the rear of the FIP module. NVRAM 128 KB 10 Mbps, half/full-duplex Copper ports (MDI/MDIX Combo interface... -
Page 106: Technical Specifications
(3) SFP+ port 0 (4) SFP+ port 1 (5) Combo interface 2 (6) Combo interface 0 (7) HIM/MIM slot Technical specifications Item Specification Flash 8 MB • Default—Two 2-GB DDR3 SDRAMs • Maximum—Two 2-GB DDR3 SDRAMs Memory type and size Install the DDR3 SDRAMs in subslots 1 and 3 in the rear of the FIP module. -
Page 107: 101
FIP-600 Front panel Figure 83 FIP-600 front panel (1) Combo interface 1 (2) Combo interface 0 (3) Slot 1 (4) Slot 2 (5) OPEN BOOK mark Technical specifications Item Specification Flash 8 MB • Default—Two 2-GB DDR3 SDRAMs Memory type and size •... -
Page 108: Sap-48Gbe
SAP-48GBE Front panel Figure 84 SAP-48GBE front panel (1) LEDs for GE ports 0 to 47 (2) SAP module status LED (RUN) (3) GE ports 0 to 47 (4) Ejector lever (5) Captive screw Technical specifications Table 50 SAP-48GBE specifications Item Specification Flash... -
Page 109: Sap-48Gbp
(5) Captive screw Technical specifications Item Specification Flash 4 MB • Default—Two 1-GB DDR2 SDRAMs Memory type and size • Maximum—Two 2-GB DDR2 SDRAMs NVRAM 128 KB 24 fiber Ethernet ports Fixed Ethernet ports (SFP) Supporting 100/1000 Mbps autosensing Dimensions (H × W × D) 45 ×... -
Page 110: Sap-4Exp
Fixed Ethernet port specifications Specifications of the SAP-48GBP fixed Ethernet ports and the FIP-110 fiber combo ports are the same. For more information, see Table SAP-4EXP Front panel Figure 87 SAP-4EXP front panel (1) SFP+ ports 0 to 3 (2) SAP module status LED (RUN) (3) LEDs for SFP+ ports 0 to 3 (4) Ejector lever (5) Captive screw... -
Page 111: Sap-20Ge2Xp
SAP-20GE2XP Front panel Figure 88 SAP-20GE2XP front panel (1) SFP ports (GE0 to GE15) (2) Combo interfaces (GE16 to GE19) (3) SFP+ port 0 (4) SFP+ port 1 (5) Operating status LED (RUN) Technical specifications Item Specification Flash 8 MB. •... -
Page 112: Sap-28Ge
Table 52 Combo copper port specifications Item Specification Connector type RJ-45 Interface type Auto MDI/MDI-X • Ethernet_II Frame format supported • Ethernet_SNAP 10 Mbps auto-sensing Half/full duplex, auto-negotiation Interface speed and 100 Mbps auto-sensing Half/full duplex, auto-negotiation duplex mode 1000 Mbps auto-sensing Full duplex, auto-negotiation For the combo fiber port specifications, see Table... -
Page 113: Spes/Oaps
Item Specification SFP ports 16 × SFP ports, 100/1000 Mbps auto-sensing. • Copper port—Straight-through/crossover autosensing: Combo interfaces 10/100 Mbps, half/full-duplex. 1000 Mbps, full-duplex. • Fiber port—1000 Mbps, full-duplex. Hot swapping Supported. Fixed Ethernet port specifications Table 54 SFP port specifications Item Specification Connector type... -
Page 114: Transceiver Modules
Transceiver modules For more information about transceiver modules supported by the HSR6800 routers, see HPE FlexNetwork 6600/HSR6600/HSR6800 Router Series Interface Module Guide. Lightning protector for a port If part of the network cable of a copper Ethernet port must be routed outdoors, connect a lightning protector to the cable before you plug the cable into the port. -
Page 115: Appendix B Leds
Appendix B LEDs HPE HSR6800 routers provide LEDs for FRUs to indicate their operating status. MPU and switching fabric module LEDs The LEDs for the RSE-X2 and RSE-X3 are the same. The following uses the RSE-X2 as an example. Figure 90 RSE-X2 LEDs Table 56 RSE-X2 LED description Status Description... - Page 116 Status Description The MPU is in standby state. Steady on The MPU is in active state. (green) No power input is available, or the MPU has failed. Slow flashing (1 The MPU is operating correctly. The system software is being loaded. (green) Fast flashing (8 CAUTION:...
-
Page 117: Lpu Leds
LPU LEDs FIP LEDs FIP-110/FIP-210/FIP-240/FIP-600 LEDs Figure 92 FIP-110 status LED Figure 93 FIP-210 status LED Figure 94 FIP-240 status LED... - Page 118 Figure 95 FIP-600 status LED Table 58 FIP-110/FIP-210/FIP-240/FIP-600 LED description Status Description No link is present. Steady green A 1000 Mbps link is present. Status LEDs Data is being received or transmitted at 1000 Flashing green for GE 0 to GE Mbps.
- Page 119 Table 59 FIP-300 LED description Status Description No link is present. Steady green A 1000 Mbps link is present. Status LEDs Data is being received or transmitted at 1000 Flashing green for GE 0 to GE Mbps. Steady yellow A 10/100 Mbps link is present. (yellow/green) Data is being received or transmitted at 10/100 Flashing yellow...
-
Page 120: Sap Leds
Status Description No link is present. Steady green A 1000 Mbps link is present. Status LEDs for SFP 0 to Data is being received or transmitted at 1000 Flashing green SFP 3 Mbps. (yellow/green) Steady yellow The transceiver module has failed the POST. No power input is available or the FIP has failed. - Page 121 Status Description No power input is available or the SAP-48GBE has failed. Slow flashing (1 Hz) The SAP-48GBE is operating correctly. System software is being loaded or the SAP-48GBE is not operating. (green) CAUTION: Fast flashing (8 Hz) To avoid hardware damage, do not power off the router, or insert or remove the SAP-48GBE when system software is being loaded.
- Page 122 Table 63 SAP-48GBP LED description Status Description No power input is available or the SAP-48GBP has failed. Slow flashing (1 Hz) The SAP-48GBP is operating correctly. System software is being loaded or the SAP-48GBP is not operating. (green) CAUTION: Fast flashing (8 Hz) To avoid hardware damage, do not power off the router, or insert or remove the SAP-48GBP when system software is being loaded.
- Page 123 Figure 102 SAP-20GE2XP LEDs Table 65 SAP-20GE2XP LED description Status Description No power input is available or the SAP-20GE2XP has failed. Slow flashing (1 Hz) The SAP-20GE2XP is operating correctly. System software is being loaded or the SAP-20GE2XP is not operating. (green) CAUTION: Fast flashing (8 Hz)
-
Page 124: Spe Leds
Figure 103 SAP-28GE LEDs Table 66 SAP-28GE LED description Status Description No power input is available or the SAP-28GE has failed. Slow flashing (1 Hz) The SAP-28GE is operating correctly. System software is being loaded or the SAP-28GE is not operating. (green) CAUTION: Fast flashing (8 Hz) -
Page 125: Him/Mim Leds
HIM/MIM LEDs For HIM/MIM LED description, see HPE FlexNetwork 6600/HSR6600/HSR6800 Router Series Interface Module Guide. Power supply LEDs Figure 104 PSR650-A AC power supply LED Figure 105 PSR1200-A AC power supply LED Figure 106 PSR650-D DC power supply LED Figure 107 PSR1200-D DC power supply LED... -
Page 126: Fan Leds
Table 67 AC/DC power LED description Status Description Steady green The power supply is operating correctly. Power LED Steady red The power supply is faulty. No power is input. Fan LEDs Figure 108 Fan LEDs for the HSR6802... - Page 127 Figure 109 Fan LEDs for the HSR6804 Figure 110 Fan LEDs for the HSR6808 Table 68 Fan LED description Status Description The system is powered off or the fan tray is faulty. Steady on The fan is operating correctly. (green)
- Page 128 Status Description The fan is operating correctly. Steady on The fan is faulty. (red)
-
Page 129: Appendix C Arranging Slots And Numbering Interfaces
Appendix C Arranging slots and numbering interfaces Slot arrangement The router provides many types of interfaces, such as console, AUX, GigabitEthernet, serial (synchronous), POS, and E1 ports. This chapter describes how these interfaces are numbered. Figure 111 Slot arrangement on the HSR6802 Figure 112 Slot arrangement on the HSR6804... -
Page 130: Available Slots For Cards
Figure 113 Slot arrangement on the HSR6808 NOTE: Figure 111 through Figure 113, the blue and dark numbers represent slot numbers of the cards and power supplies, respectively. Available slots for cards Card HSR6802 HSR6804 HSR6808 RSE-X2/RSE-X3 (supporting 1+1 Slot 0 and Slot 1 Slot 0 and Slot 1 Slot 4 and Slot 5 redundancy) -
Page 131: Numbering Interfaces
Numbering interfaces Before installing a HIM/MIM, you must install a FIP. The interfaces of the router are numbered in the form of interface-type X/Y/Z, Where, • interface-type—Type of the interface such as GE port and serial port. • X—Number of the slot where the FIP/SAP resides (for example, blue numbers in Figure 111 through Figure... -
Page 132: Appendix D Cable Management
Appendix D Cable management When the router is mounted in a 19-inch standard rack, the interface cables are routed through the cable management brackets, bound at cabling racks on chassis sides, and then routed up or down, depending on the available equipment room condition. The power cables run along the two sides of the front of the chassis and out of the chassis either from the chassis top or the raised floor depending on the equipment room conditions (power distribution cabinet, lightning protection box, and connector strip, etc.) of the exchange office. - Page 133 Figure 114 Correct and incorrect cable binding • Route different types of cables (for example, power cables, and signal cables) separately. If they are close to one another, cross them over one another. If you route them in parallel, make sure the space between a power cable bundle and a signal cable bundle is a minimum of 30 mm (1.18 in).
- Page 134 Figure 116 Binding the cables • Route, bind, and attach excess cables for easy, safe maintenance activities and correct operations. • Do not tie the power cables to the slide rails. • When you connect a cable to an articulated part, for example, when you connect a grounding cable to a cabinet door, leave enough slack in cables and make sure they are not stressed from any movement of the part.
-
Page 135: Cable Routing Example
• Do not tie cables or bundles in a knot. • The metal parts of the crimped cold-pressed terminal blocks (such as circuit breaker) cannot protrude beyond the blocks. Cable routing example Cables on the router can be routed as shown in Figure 118. -
Page 136: Appendix E Hardware Compatibility Matrixes
Appendix E Hardware compatibility matrixes In the compatibility matrixes, "√" means "Supported" and "×" means "Not supported." MPU and Comware compatibility matrix Table 70 MPU and Comware compatibility matrix Comware 5 Comware 7 RSE-X2 √ × RSE-X3 × √ LPU and Comware compatibility matrix Table 71 LPU and Comware compatibility matrix Comware 5 Comware 7... -
Page 137: Index
Index A C D E F G H I L M N P R S T Installing a CF card,17 Installing a HIM,16 Active and standby switchover for MPUs,58 Installing a MIM,17 Available slots for cards,124 Installing a power supply,13 Installing an LPU,15 Installing an MPU and a switching fabric... - Page 138 Replacing a transceiver module,45 Software upgrade failures,72 Replacing an air filter,47 LEDs,118 Replacing an LPU,43 SPE/OAP,107 Replacing an MPU and a switching fabric module,41 Surge lightning protector,108 Switching fabric module,94 System software image file missing errors,73 Safety recommendations,1 Safety recommendations,41 Slot arrangement,123 Troubleshooting system...
Need help?
Do you have a question about the FlexNetwork HSR6802 and is the answer not in the manual?
Questions and answers