HP FlexNetwork HSR6600 Configuration Manual page 368

[PE1-bgp-default-vpnv6] quit
# Redistribute direct routes to the VPN routing table of vpn1.
[PE1-bgp-default] ip vpn-instance vpn1
[PE1-bgp-default-vpn1] address-family ipv6 unicast
[PE1-bgp-default-ipv6-vpn1] import-route direct
[PE1-bgp-default-ipv6-vpn1] quit
[PE1-bgp-default-vpn1] quit
[PE1-bgp-default] quit
2. Configure ASBR-PE 1:
# Enable IS-IS on ASBR-PE 1.
<ASBR-PE1> system-view
[ASBR-PE1] isis 1
[ASBR-PE1-isis-1] network-entity 10.222.222.222.222.00
[ASBR-PE1-isis-1] quit
# Configure LSR ID, and enable MPLS and LDP.
[ASBR-PE1] mpls lsr-id 3.3.3.9
[ASBR-PE1] mpls ldp
[ASBR-PE1-ldp] quit
# Configure interface Serial 1/1/0, and enable IS-IS, MPLS, and LDP on the interface.
[ASBR-PE1] interface serial 1/1/0
[ASBR-PE1-Serial1/1/0] ip address 1.1.1.1 255.0.0.0
[ASBR-PE1-Serial1/1/0] isis enable 1
[ASBR-PE1-Serial1/1/0] mpls enable
[ASBR-PE1-Serial1/1/0] mpls ldp enable
[ASBR-PE1-Serial1/1/0] quit
# Configure interface Serial 1/1/1, and enable MPLS.
[ASBR-PE1] interface serial 1/1/1
[ASBR-PE1-Serial1/1/1] ip address 11.0.0.2 255.0.0.0
[ASBR-PE1-Serial1/1/1] mpls enable
[ASBR-PE1-Serial1/1/1] quit
# Configure interface Loopback 0, and enable IS-IS on it.
[ASBR-PE1] interface loopback 0
[ASBR-PE1-LoopBack0] ip address 3.3.3.9 32
[ASBR-PE1-LoopBack0] isis enable 1
[ASBR-PE1-LoopBack0] quit
# Enable BGP on ASBR-PE 1.
[ASBR-PE1] bgp 100
[ASBR-PE1-bgp-default] peer 2.2.2.9 as-number 100
[ASBR-PE1-bgp-default] peer 2.2.2.9 connect-interface loopback 0
[ASBR-PE1-bgp-default] peer 11.0.0.1 as-number 600
[ASBR-PE1-bgp-default] peer 11.0.0.1 connect-interface serial 1/1/1
# Disable route target based filtering of received VPNv6 routes.
[ASBR-PE1-bgp-default] address-family vpnv6
[ASBR-PE1-bgp-default-vpnv6] undo policy vpn-target
# Configure IBGP peer 2.2.2.9 and EBGP peer 11.0.0.1 as VPNv6 peers.
[ASBR-PE1-bgp-default-vpnv6] peer 11.0.0.1 enable
[ASBR-PE1-bgp-default-vpnv6] peer 2.2.2.9 enable
358